JX-300LED_SPE_EN01.pdf - 第13页

- 9 - 4.3 Component Placement Cycle Time (Number of Components Placed for One Hour) (1) 1005 Square chip (conforming to IPC9850) Component height specifications Cycle time (CPH) SC(6mm) 19,300 NC(12mm) 18,800 *1 This i s…

- 8 -

4.2.2 Outside dimensions (except for the largest projections)

JX-300LED

(Unit: mm)

Size Standard

When a longer-sized board

(X-dimension: 1,500 mm) is

supported

Conveyor

height

900 only 900 only

A 1,920 2,520

B 210 510

C 1,710 *1

－

1,500 *2

*1 When a board is transported, the conveyor extension “B” on one side (IN side) is to be

removed from the standard machine according to the board transport specification.

*2 When a longer-sized board support option is attached on the machine, the conveyor

extensions “B” on both sides are to be removed from the machine.

4.2.3 Mass of the main unit

Standard machine: 1,420 kg

D (1,500 mm: length of the conveyor equipped with an option

when a board is transported)

265

1393

C (Length of the LR specification conveyor when a board is transported)

C (Length of the RL specification conveyor when a board is transported)

1685

1,300 (Width of the main unit)

000

1440

900

- 9 -

4.3 Component Placement Cycle Time

(Number of Components Placed for One Hour)

(1) 1005 Square chip (conforming to IPC9850)

Component height

specifications

Cycle time (CPH)

SC(6mm) 19,300

NC(12mm) 18,800

*1 This is a number of components to be placed for one hour when 400 1005 square chips are

placed onto a 200 mm×200 mm board whose thickness is 2.5 mm at an angle of 0, 90 180 and

270 degrees sequentially. (This operation conforms to IPC9850.)

*2 This cycle time is measured when an 8-mm tape feeder is used, and components are placed on

boards sequentially after the L1 to L6 nozzles are used to pick them up simultaneously and a

component existence check is run.

*3 This measurement is performed under the optimal conditions except for the check functions

such as a component tombstone error.

(2) LED square chip

Component height

specifications

Cycle time (CPH)

SC(6mm) 18,200

NC(12mm) 17,300

*1 This is a number of components to be placed for one hour when LED square chips are placed

on boards sequentially according to the JUKI designated placement pattern. (This figure does

not include any mark recognition time.)

*2 This cycle time is measured when Six feeders(12-mm tape) is used, and components are

placed on boards sequentially after the L1, L3 and L5 nozzles are used to pick them up

simultaneously, the L2, L4 and L6 nozzles are used to pick them up simultaneously and a

component existence check is run.

*3 This measurement is performed under the optimal conditions except for the check functions

such as a component tombstone error.

(3) LED diffusing lens

Component height

specifications

Cycle time (CPH)

SC(6mm) -

NC(12mm) 10,000

*1 This is a number of components to be placed for one hour when LED diffusing lenses are placed

on boards sequentially according to the JUKI designated placement pattern. (This figure does

not include any mark recognition time.)

*2 This cycle time is measured when Six feeders(12-mm tape) is used, and components are

placed on boards sequentially after the L1, L3 and L5 nozzles or the L2, L4 and L6 nozzles are

used to pick up three lenses simultaneously and a component existence check is run.

*3 This measurement is performed under the optimal conditions except for the check functions

such as a component tombstone error.

- 10 -

4.4 Nozzles

Various types of nozzles have been designed to increase the reliability of placement of

each type of components as shown in the table below.

For a standard nozzle to be attached on the JX-300LED, select it from among the nozzles

shown in the table below.

Table Nozzles supplied as the standard devices

Nozzle Nozzle assembly

Applicable components

(reference) and remarks

NO.

Internal

diameter

of a nozzle

External

diameter

of a nozzle

A B D E F G H

Std.

Nozzle

select

500 2-φ0.4 1.0 x 0.5 − 6 − − − − −

1005, 1608, 2012

See Note2

SOT (Molding: 1.6 x 0.8)

501 φ0.25 0.7 x 0.4 − − 6 − − −

0603

502 φ0.4 φ0.7 6 − 6 3 − − 3

1005

503 φ0.6 φ1.0 6 − 3 6 3 6 3

1608, 2012, SOT (Molding:

1.6 x 0.8), SOT (Molding:

2.0 x 1.25)

504 φ1.0 φ1.5 − 4 1 3 6 6 3

2012, 3216, SOT23, SOT

(Molding: 2.0 x 1.25)

505 φ1.7 φ3.5 1 2 − 3 3 1 3

Aluminum electrolytic

capacitor

(small), tantalum electrolytic

capacitor, trimmer

506 φ3.2 φ5.0 1 1 − 1 3 1 3

Aluminum electrolytic

capacitor (medium),

SOP (narrow type),

SOJ, Connector

507 φ5.0 φ8.5 1 1 − − 1 1 1

Aluminum electrolytic

capacitor (large),

SOP (wide type),

TSOP, QFP, PLCC,

Connector

508C φ8.0 φ9.5 1 1 1 1 1 1 1

See

Note1

QFP, PLCC, BGA

Total number of nozzles 16 15 17 17 17 16 17 15

* Total number of nozzles that can be installed onto an ATC station: 26 pieces.

Note 1: As a Std. Nozzle Select, you can select 15 nozzles among those whose number is from

500 to 508C.

However, you have to select a nozzle to be used for calibration of the machine:

- For laser calibration (one of the nozzles choose from 500, 502 and 503)

- For calibration (508C nozzle)

Note 2: Since a theta error may occur due to the shape of the surface of a 2012R component to

be picked, use a No. 504 nozzle if you have to place 2012R components in the high

density (the gap between the adjacent components: 0.3 mm or less).