00194591-01.pdf - 第9页
Installation Guide SIPLACE Setup Center 2 System Compon ents and Configurations Edition 03/2005 EN 2.1 Overview of System Components 9 2 System Component s and Configurations 2.1 Ove rview of Sys tem Co mponen t s A comp…
1 Introduction Installation Guide SIPLACE Setup Center
1.4 Navigation Guide for Installation Edition 03/2005 EN
8
Note:
A hard disk with 500 MB or more free space should be used for installation (without the operating
system installed there should be at least 1 GB free space).
Thesizeof thedatabase willgrowconstantlyas additionaldatais stored, thisshouldbe takeninto
consideration. 1
1.4 Navigation Guide for Installation
Please use the following documents to lead you through the installation procedure for SIPLACE
Setup Center. 1
1
1
Fig. 1 - 1 Navigation Guide for Installation
1
SIPLACE Pro Desk
Installation of SIPLACE Pro 2.0
(00193435-02)
SIPLACE Setup Center 2.0
Getting Started
(00194592-01)
Installation Guide SIPLACE Setup Center 2 System Components and Configurations
Edition 03/2005 EN 2.1 Overview of System Components
9
2 System Components and
Configurations
2.1 Overview of System Components
A complete installation of SIPLACE Setup Center consists of the following components. 2
– SIPLACE Setup Center GUI
– SIPLACE Setup Center Database
2.1.1 System Configuration
There are several different recommended installation scenarios for SIPLACE Setup Center. The
installation depends on the working area where SIPLACE Setup Center will be used and on other
conditions as described below. 2
2.1.1.1 SIPLACE Setup Center Database
The most importantdecision before thefirst installation iswhichtype of datamanagement is used.
The following decision tree should give you support with this decision. Please read through the
questions thoroughly andfollow the appropriate result path. As a result you get the recommended
kind of installation for the SIPLACE Setup Center database. 2
2
Fig. 2 - 1 Decision Tree for SIPLACE Setup Center Database
No Yes
No Yes
LocalDatabase
(MSDE)
Central Database
Do you validate the setup
in a pre-setup area?
Do the packaging units
have Unique ID barcodes?
2 System Components and Configurations Installation Guide SIPLACE Setup Center
2.1 Overview of System Components Edition 03/2005 EN
10
Questions:
– Do the packaging units have Unique ID barcodes?
Each packaging unit in the factory must be marked with a unique barcode. It is possible that
the unique ID is part of a combined barcode.
2
– Do you validate the setup in a pre-setup area?
The pre-setup area is used to validate the setup for correctness and completeness. The vali-
dated tables are docked to the production line(s) for use.
2
– Local database (MSDE)
This scenario does track the numbers of components on each packaging unit. The current
number of componentsare "remembered" when the packaging unit is teared down. If the pack-
aging unit is moved to another line the other Setup Center system does not know this reel and
will start with the start quantity. Therefore the operator need to check each partially fractured
packaging unit he gets from the stock and need to adjust the quantity if necessary.
2
This scenario offers a higher amount of operation safety, because the SIPLACE Setup Center
and a local MSDE database are installed to different computers for each production line. Ifone
componentofSIPLACESetupCenterencountersanerror,onlyoneproductionlineisaffected.
2
– Central database
The SIPLACE Setup Center database can be installed to any available Microsoft SQLServer
2000 (SP3a). In this case, the customer is responsible to set up a backup & recovery strategy
and must provide an operating Microsoft SQLServer2000(SP3a).
2
2.1.1.2 Setup Center GUI
It is recommended to install SIPLACE Setup Center GUI once for each line. With the "central da-
tabase" scenario these can use the same database at the same time.
2
It is recommended to use two barcode scanners per line and SIPLACE Setup Center GUI instal-
lation.
2
2