5965-4792.pdf - 第36页

U p to 3 G Hz (7 mm ) : SM D c ontinu ed Exchanging the device holder 1. Remo ve the gro und plat e 2. When me asur ing SMD, at tach t he knob on the device holder . 3. Select the dev ice holder su i table for the d evic…

16194A High tempera-

ture component test fixture

Terminal connector: 7 mm

DUT connection: 2-Terminal

Electrical length: 50 mm

Dimensions (approx.):

150 (W) x 40 (H) x 80 (D) [mm]

Weight (approx.): 350 g

Additional error:

SMD:

Leaded device:

f: [GHz]

Up to 3 GHz (7 mm): SMD continued

Description: This test fixture is designed for measuring both axial/radial leaded devices

and SMD within the temperature range from –55 to +200 °C (when used with the

E4991B-007 Temperature Characteristic Test Kit, –55 to +150 °C).

Applicable instrument: E4982A, E4990A + 42942A*, E4991B, E5061B-3L3/3L4/3L5

with Opt. 005 + 16201A

* Option E4990A-120 is required

Frequency:

DC to 500 MHz (with open and short compensation)

DC to 2 GHz (with open and short and load compensation)

Maximum voltage: ±42 V peak max. (AC+DC)

Operating temperature: –55 to +200°C

DUT size: See figure below.

Type of error Impedance

Proportional error 20 x f

[%]

Open repeatability 80 + 250 x f [

Short repeatability 0.2 + 2.5 x f [Ω]

Type of error Impedance

Proportional error 20 x f

[%]

Open repeatability 80 + 500 x f [

Short repeatability 0.4 + 12.5 x f [Ω]

Description P/N Qty. Option

Wrench 8710-1181 1 Standard

Tweezers 8710-2081 1 Standard

50Ω SMD resistor 0699-2829 10 Standard

Operation and service manual 16194-90030 1 Standard

General sized

Shorting device

(1 x 1 x 2.4 (mm))

Shorting device

(1.6 x 2.4 x 2 (mm))

Shorting device

(2.4 x 2.4 x 3.2 (mm))

Shorting device

(2.4 x 2.4 x 4.5 (mm))

16191-29001

16191-29002

16191-29003

16191-29004

16192A-701

EIA/EIAJ industrial standard sized

Shorting device

(1 x 0.5 x 0.5 (mm))

Shorting device

(1.6 x 0.8 x 0.8 (mm))

Shorting device

(2.0 x 1.2 x 0.8 (mm))

Shoring device

(3.2 x 1.6 x 0.8 (mm))

16191-29005

16191-29006

16191-29007

16191-29008

16192A-010

Case for shorting devices 1540-0692 1 16192A-010/701

Furnished accessories:

32 | Keysight | Accessories Catalog for Impedance Measurements - Catalog

Up to 3 GHz (7 mm): SMD continued

Exchanging the device holder

1. Remove the ground plate

2. When measuring SMD, attach the

knob on the device holder.

3. Select the device holder suitable for

the device type. Loosen its knob and

insert into the arm.

4. Set the ground plate.

Placing the device

16194A High temperature component test fixture continued

Options:

16194A-010: Add EIA/EIAJ industrial standard sizedshorting bar set

16194A-701: Add general sized shorting bar set

Compensation and measurement: Before beginning the measurement, the appropriate

device holder (for a SMD or lead component) must be prepared with the text fixture. The

following figure shows how the device holder is exchanged to match the device type.

The next step is to perform open and short compensations in combination with the

electrical length compensation. When measuring above 500 MHz, load compensation

is also recommended. The fixture’s electrical length must be entered into the electrical

length compensation function of the measurement instrument first. Then open com-

pensation is performed by separating the high and the low electrodes from each other.

The separation should be equivalent in size to the DUT’s width. Short compensation is

performed by using the option 16194A-010/701 shorting bar set. Load compensation is

performed by using the furnished 50 Ω SMD chip resistor. After performing open, short,

and load compensations in combination with the electrical length compensation, the

DUT is inserted into the test fixture. The following figures show how measurement is

performed.

33 | Keysight | Accessories Catalog for Impedance Measurements - Catalog

16196A Parallel electrode SMD

test fixture

Terminal connector: 7 mm

DUT connection: 2-Terminal

Electrical length: 26.2 mm

Dimensions (approx.):

140 (W) x 48 (H) x 78 (D) [mm]

Weight (approx.): 250 g

Additional error:

f: frequency [GHz]

Fixture overview

Up to 3 GHz (7 mm): SMD continued

Description: This test fixture is designed for impedance evaluations of parallel electrode

SMDs. It achieves stable frequency characteristics up to 3 GHz and provides highly

repeatable measurements. The applicable SMD size code is 0603 (inch)/1608 (mm).

Applicable instrument: E4982A, E4990A + 42942A*, E4991B, E5061B-3L3/3L4/3L5

with Opt. 005 + 16201A

* Option E4990A-120 is required

Frequency: DC to 3 GHz

Maximum voltage: ±42 V peak max. (AC +DC)

Operating temperature: –55 to +85°C

DUT size: The applicable SMD size is 0603 (inch)/1608 (mm). For details, see the figure

below.

The 16196A is furnished with three different insulator assemblies, since any gaps

between the DUT and the cylindrical insulator will result in improper positioning and

subsequent measurement errors. Select an insulator assembly that reduces the gap the

most. See the table below for dimensions of the insulator assemblies.

1. Opt. 16196A-710 only

Type of error Impedance

Proportional error 1.0 x f

[%]

Open repeatability 5 + 40 x f [

Short repeatability 30 + 125 x f [mΩ]

Description P/N Qty.

Operation and service manual 16196-90040 1

Insulator assembly ϕ1.34 mm 16196-60112 1

Insulator assembly ϕ1.14 mm 16196-60113 1

Insulator assembly ϕ1.08 mm 16196-60114 1

Open plate 16196-29002 1

Short plate 16196-29026 1

Push ring 16196-24004 1

Magnifying Lens

16193-60002 1

Tweezers 8710-2081 1

Wrench 8710-0909 1

Cleaning rod 5182-7586 1

Carrying case 16196-60150 1

Hole diameter of insulator

assembly (mm)

SMD case size examples

Length, width, height (mm)

16196A ϕ1.34 1.6 x 0.8 x 0.8

ϕ1.14 1.6 x 0.8 x 0.6

ϕ1.08 1.6 x 0.8 x 0.5

E4982A with 16196A

Furnished accessories:

34 | Keysight | Accessories Catalog for Impedance Measurements - Catalog