4OM-1011-002.pdf - 第173页

0305-001 Tg0860-PM-MM *5 “COMP . LIBRARY INFO./FDR. OFFSET INFO” Displayed are the component library data and the feeder offset of the feeder No. set up in *1. *6 “RESUL T X (mm), Y (mm)” When the manual alignment operat…

0305-001 Tg0860-PM-MM

*2 “SELECT OPTION”

[FEEDER (B) OFFSET] Key

When the display (Fig. 4C232) is active and this key is

pressed, the display (Fig. 4C231) appears on the screen.

Use this function to perform the teaching operation on

the component center position.

[TEACH ECC. PICKUP POS [PICKUP LOC. ADJ]] Key

When the display (Fig. 4C231) is active and this key is

pressed, the display (Fig. 4C232) appears on the screen.

Use this function when a component has a groove, a

protrusion, etc., and cannot be picked up at the center

without any hindrance.

*3 “TEACH MENU”

“FEEDER (B) OFFSET (X, Y)” is modified additionally.

[CENTER 1-PT.] Key

When this key is pressed, the X/Y beam moves to the

center of the component.

“1POINT” and “2POINT”

These labels are used to align the component with two

diagonally-located points.

When the maximum outside dimensions of the compo-

nent exceeds “10 × 10 mm”, use these keys.

*4 “TEACH MENU”

[ALL BM. HD. ZERO] Key

This key is used to zero both Beams A and B.

When this key is selected and the [MOVE] button is

pressed, the zeroing operation starts.

[ECCENTRIC PT.] Key

When this key is selected and the [MOVE] button is

pressed, the P.E.C. recognition camera moves to the des-

ignated pick-up location correction position based on the

component center position (Position of “Design Position

+ Feeder (A) Offset + Feeder (B) Offset”) of the perti-

nent feeder, making it possible to capture the image.

Under this condition, shift to the trackball operation and

perform the manual alignment operation.

Note: It is necessary to correctly teach the component

center position before the eccentric position is

adjusted.

3-121

6.12 PICK-UP LOCATION (TRAY) Display (Option)

Fig. 4C234

Fig. 4C235

Fig. 4C236

CAUTION

“PICK-UP LOCATION ADJUST-

MENT X, Y” in the component li-

brary data is modified additionally.

Incorrect teaching operation will

cause the pick-up rate to deterio-

rate.

0305-001 Tg0860-PM-MM

*5 “COMP. LIBRARY INFO./FDR. OFFSET INFO”

Displayed are the component library data and the feeder

offset of the feeder No. set up in *1.

*6 “RESULT X (mm), Y (mm)”

When the manual alignment operation (using the trackball)

is completed, the results of the teaching operation are dis-

played.

Selection of [FEEDER (B) OFFSET] Key: FEEDER (B)

OFFSET

Selection of [TEACH ECC. PICKUP POS [PICKUP LOC.

ADJ]] Key: PICK-UP LOCATION ADJUSTMENT

*7 “TRAY MATRIX”

Shown are the coordinates (X, Y) which represent the pick-

up matrices of the selected tray.

*8 [TRAY MATRIX EDIT] Key

When this key is pressed, the display (Fig. 4C243) appears

on the screen.

Use this function to edit the pick-up matrices.

*9 “ALL BEAM ZERO”

When all beams are zeroed completely, the background turns

green. Otherwise, the background has no color.

*10 “RECOG. COMM.”

When “DISABLE” is set in the “P.E.C.” and “COMPO

NENT RECOGNITION” data boxes at the “TEST

MODE” display, the background color of “P.E.C. RECOG.”

and “COMP. RECOG.” becomes light red.

(No background color in normal cases)

Operation Procedure

Refer to “6.10 PICK-UP LOCATION (TAPE･VIB.

STICK) Display” for details.

3-122

6.12 PICK-UP LOCATION (TRAY) Display (Option)

Fig. 4C237

Fig. 4C238

Fig. 4C239

Fig. 4C240

Fig. 4C241

Fig. 4C242

0305-001 Tg0860-PM-MM

6.12.3 PICK-UP LOCATION TEACH - TRAY MATRIX EDIT

Display (Option)

• This display allows the editing of the pick-up matrices.

When the [TRAY MATRIX EDIT] key is pressed at the "FEEDER (B)

OFFSET･ECC. LOCATE OFFSET" display, the following display appears on

the screen.

*1 “PICK-UP MAT X, Y”

The pick-up matrices X and Y can be changed.

*2 [ ] Key

When this key is pressed, the “COMPONENT ID” field shifts horizontally

to the left, enabling you to view the first part of component IDs.

*3 [ ] Key

When this key is pressed, the “COMPONENT ID” field shifts horizontally

to the right, enabling you to view the comments.

Operation Procedure

(1) Select the key under “X” or “Y”.

(2) Specify the matrix position, using the ten-key pad.

(3) Press the [SET] key.

3-123

6.12 PICK-UP LOCATION (TRAY) Display (Option)

Fig. 4C243