4OM-1011-002.pdf - 第37页

Tg0860-PM-MM 0307-002 1-22 8. Maintenance (Every 3 Months) Fig. 4A29 Control Box Dust Filter Cleaning ( 1) After removing the setscrews, draw it out, holding the knobs on the right and left sides. ( 2 ) Clean dirt and du…

0305-001 Tg0860-PM-MM

1-21

Air Filters

Cleaning

(1) Remove the air filter.

Align the mark with the release position by pressing

and turning the button at the same time. Then, draw the

outer case downward to remove. Remove the inner air

filter by turning it in the direction of Arrow A.

(2) Blow off dust with compressed air.

(3) Mount the air filter.

Mount the air filter turning it in the direction of Ar-

row B.

Mount the outer case and at the same time press and

turn the button to align the mark with the locking

position.

Button

Lock

Unlock

Table 4A9

8. Maintenance (Every 3 Months)

Fig.4A27 Air Regulator

Maintenance Spots Check

Name

Fig.

No.

Description Grease

Cleaning

Tools,

Nozzles, etc.

Air Regulator Air Filters 4A27 Cleaning − − − Air Gun

Vacuum Pressure

System

Aggregated Vacuum

Filter

4A28 Cleaning − − − Air Gun

Control Box Dust Filter 4A29 Cleaning − − − Vacuum

Cleaner

Beam A side

Tg0860-PM-MM

0307-002 1-22

8. Maintenance (Every 3 Months)

Fig. 4A29 Control Box

Dust Filter

Cleaning

(1) After removing the setscrews,

draw it out, holding the knobs on

the right and left sides.

(2) Clean dirt and dust with a vacuum

cleaner.

Fig. 4A28 Vacuum Pressure System

Filter Case

Aggregated Vacuum Filter

Cleaning

(1) Remove the filter case by turn-

ing in the direction of Arrow C

and remove the inner filter.

(2) Blow off dust with compressed air.

Beam A side

Unit : mm

Note: The dimensions in the figures

are design values.

Knob

Setscrew

CAUTION

Use protective devices to avoid any accident which

may be caused due to the tight work space.

954

810

523

0305-001 Tg0860-PM-MM

9. Maintenance (Every 6 Months)

Notes: (a) Grease Symbols

DE1 : DAPHNE EPONEX GREASE No.1

NM1 : NEW MOLYNOC GREASE No.1

KS64 : SILICONE GREASE KS64

(b) If SILICONE GREASE KS64 (SHIN-ETSU CHEMICAL CO.) is not

available, use grease specified as follows.

Fluorine Type Grease, BARRIERTA IEL/V (NOK KLUBER)

When BARRIERTA IEL/V is used, gently wipe grease over spots to be

lubricated.

1-23

9. Maintenance (Every 6 Months)

Maintenance Spots Check

Name

Fig.

No.

Description Grease

Cleaning

Tools,

Nozzles, etc.

PCB Positioning

Section

Linear Guide 4A30 Cleaning and

Lubrication

DE1 Oiled Rag,

Hand or

Brush

Ball Spline

4 places

4A31 Cleaning and

Lubrication

DE1 Oiled Rag,

SPK-3C

Conveyor Linear Guides

(4 nipples)

4A32 Cleaning and

Lubrication

DE1 Oiled Rag, U

and N Types

Ball Screws and Nut 4A32 Cleaning and

Lubrication

DE1 Oiled Rag,

Hand or

Brush

Splines 4A32 Cleaning and

Lubrication

NM1 Oiled Rag,

Hand or

Brush

X-Axis

Side of Cable

4A33 Cleaning and

Lubrication

KS64 Oiled Rag,

Hand or

Brush

X-Axis

Cable Fixing Position

4A33 Checking − − − − − − −

X-Axis

Upper/Lower Cable

Guides

4A33 Cleaning and

Lubrication

KS64 Oiled Rag,

Hand or

Brush

Y-Axis

Side of Cable

4A34 Cleaning and

Lubrication

KS64 Oiled Rag,

Hand or

Brush

Y-Axis

Cable Fixing Position

4A34 Checking − − − − − − −

X/Y Beam

(Beams A and B)

Y-Axis

Lower Cable Guide

4A34 Cleaning and

Lubrication

KS64 Oiled Rag,

Hand or

Brush

Table 4A10