00192471-03.pdf - 第63页

User Manual SIPLAC E HS-50 2 Oper ational Safety Software Version SR.50x.xx 01/2006 US Edition 2.1 Safety instructions 63 2 Fig. 2.1 - 6 Label: Laser radiation 2.1.14 Safety instructions for changi ng the height of compo…

100%1 / 184
2 Operational Safety User Manual SIPLACE HS-50
2.1 Safety instructions Software Version SR.50x.xx 01/2006 US Edition
62
2.1.13 Safety instructions for the PCB barcode reader (option)
2
Fig. 2.1 - 5 PCB barcode reader
CAUTION The radiant power of the barcode reader’s scanning beam is less than 1 mW.
This means that the barcode reader conforms to laser class 2 and, according to DIN EN 60825-
1, requires no special safety equipment or protective measures. NEVER look into the laser beam.
There is also a safety circuit that switches off the laser diode if the polygon wheel stops or turns
too slowly. 2
(1) PCB barcode reader
(2) Label: LASER RADIATION...
(3) Label: CAUTION ...
User Manual SIPLACE HS-50 2 Operational Safety
Software Version SR.50x.xx 01/2006 US Edition 2.1 Safety instructions
63
2
Fig. 2.1 - 6 Label: Laser radiation
2.1.14 Safety instructions for changing the height of component tables
WARNING 2
The component table must only be converted to modify the default
height by trained Service personnel.
Act with considerable care during the conversion process since
the system contains large weights or compression springs (potential
energy).
2
Converting the component table to suit a different line height 2
Æ Use the placement system’s pneumatic controller to raise the table bed. Then insert a 120mm
spacer block between the table bed and cross-beam, and lower the bed onto the block.
Æ Dismantle the internal paneling.
Æ Swivel the handle down. The latching disk swivels down as well.
Æ Set the screw to the desired dimension and lock in place with the locknut.
PLEASE NOTE:
If you cannot loosen the adjusting screw far enough, the cross-beam must be raised. 2
Æ Fix the lifting device to the cross-beam.
Æ
Carefully
open the cross-beam clamp.
Æ Raise the cross-beam until the end of the tube projects approx. 1mm out of the clamp.
Æ Tighten the cross-beam clamp.
Æ Then turn the adjusting screw to the desired dimension and lock in place with the locknut.
2
Laser radiation
Do not look into beam
Class 2 laser product
2
Attention!
Laser radiation if the cover
is opened and the safety
interlock is bypassed.
Do not look into beam
2 Operational Safety User Manual SIPLACE HS-50
2.1 Safety instructions Software Version SR.50x.xx 01/2006 US Edition
64
Æ Swivel the component table handle up. The latching disk will also swivel up.
PLEASE NOTE:
If you cannot swivel the latching disk up to its end position, the cross-beam must be raised. 2
Æ Fix the lifting device to the cross-beam.
Æ
Carefully
open the cross-beam clamp.
Æ Raise the cross-beam until the end of the tube projects approx. 1mm out of the clamp.
Æ Tighten the cross-beam clamp.
Æ Then turn the adjusting screw to the desired dimension and lock in place with the locknut.
Æ Then
carefully
open the cross-beam clamp.
Æ Lower the cross-beam until the adjusting screw comes into contact with the latching disk.
Æ Tighten the cross-beam clamp.
Æ Then check the distance between the cross-beam and floor.
Æ Refit the internal paneling.
Æ Raise the table bed and remove the spacer block.