NXTII spec.pdf - 第11页

Machine Specifications Edition 2.0E - 1 1 - NXT II S pecifications 3.2. Base Sp ecifi cations Base Ty pe 4MII base (independent) 2MII base (independent) V acuum pump O O CPU board O O Module Capacity (Based on M3II modul…

Machine Specifications

Edition 2.0E - 10 - NXT II Specifications

3. The placing accuracy varies depending on the placing head used. The placing accuracy is obtained from

tests conducted by Fuji. Parts rotational offset is not considered. Also, the above placing accuracy may not

be obtained depending on the quality of the PCB and the parts that are placed.

4. Obtained from tests conducted by Fuji. Errors due to packaging are not included.

5. Obtained when reading a 1.2 mm diameter mark, excluding the time required to travel from mark to mark,

and to make adjustments for mark shape variations and location errors.

Machine Specifications

Edition 2.0E - 11 - NXT II Specifications

3.2. Base Specifications

Base Type

4MII base

(independent)

2MII base

(independent)

Vacuum pump O O

CPU board O O

Module Capacity

(Based on M3II module)

4 2

Configure your machine from a selection of the base sizes in the table above and

modules listed in the following module specification section.

When connecting bases, a connecting bracket is required regardless of the base

size or number of bases being connected.

An anchor bolts are required to secure the base when installing a 2MII base on

its own.

It is necessary to place adhesive sheets below the leveling sheets when

installing a 4MII base on its own or when connecting and installing two 2MII

bases.

3.3. Module Specifications

Items M3II Module M6II,M6IISP Module

Module width 325 mm

Note 1

650 mm

Note 1

Heads (selective type, one-touch

replacement available)

H12HS[H12S],H08,

H04,H02,H01,G04,GL

H12HS[H12S],H08,

H04,H02,H01,G04,OF,GL

Tape (W4P1)W8 ～ W88 mm

Stick O O

Tray unit-L X 1 unit

Tray unit-LT X 1 unit

Packaging

Tray unit-M X 1 or 2 units

L size O O

Reject parts

unit

Note 2

M size O O

Capacity (Using 8 mm tape with 7 inch

reel)

20 45 (44

Note 3

)

Standard back-up pin (magnet type)

PCB support

Auto back-up pin position function (option)

Notes:

1. A gap of 5 mm between each module has been added to the above figures for module width. The actual

dimensions for the above modules are 320 mm (M3II) and 645 mm (M6II, M6IISP) respectively.

2 Certain limitations exist based on the head type and parts height. (Refer to 7. Options.)

3. For the M6IISP, the capacity is 44.

Machine Specifications

Edition 2.0E - 12 - NXT II Specifications

Less than 14

Less than 18

3.4. Head Specifications

Items H12HS[H12S] H08 H04

No. of nozzles 12 8 4

Part size

(0402)

Note 5

0603 ~

5 × 5 mm

(6 nozzle operation is 5 x 5

mm to 7.5 x 7.5 mm)

(0402)

Note 5

0603 ~

7.5 × 7.5 mm

(4 nozzle operation is 7.5 x

7.5 mm to 12 x 12 mm)

1608 (0603) ~ 38 x 38

Note 1

Max. part height 3 mm 6.5 mm 9.5 mm

Max. premounted part height

(upper surface)

3 mm 6.5 mm 9.5 mm

Packaging Tape Tape

Tape, Trays

Note 4

Sticks

Cpk≥1.00

±0.050 ±0.050 ±0.050

Placing accuracy

Note 2

(Rectangular chips and

small odd-form parts)

Cpk≥1.33

±0.066 ±0.066 ±0.066

M3II 22500 [18000] 11000 6500

M6II 22500 [18000] 11000 6500

Throughput

Note 3

(cph (chips/hr))

M6IISP 18500 [17000] 10000 6000

Nozzle change Yes Yes Yes

Notes:

1. 4 nozzle spec.: Max. 13 × 13 mm

2+2 nozzle spec.: Max. 14 x 14 mm

(or corner to corner dimensions of

19.8 mm or less and 14 mm or less

in the Y-direction) + 11 x 11 mm

2 nozzle spec.: Max. 18 x 18 mm

(or corner to corner dimensions of 26 mm or less and 18 mm or less in the Y-direction)

1 nozzle spec: Max. 38 × 38 mm

Parts for feeders and trays should be supplied in the XY-direction as shown in the diagram below.

2. The placing accuracy above is based on tests conducted at Fuji.

3. The throughput above is based on tests conducted at Fuji.

4. When using tray unit-L, parts less than 9 mm from the lower surface of the tray to the upper surface of the

parts are not supported. However, trays up to 29.5 mm in height (thickness) are supported.

5. The following conditions are required when placing 0402(01005) parts.

a. Manual offsetting using PAM is recommended when the required placement accuracy is 0.05 mm or

less.

b. Changes to Fuji Flexa nozzle spec data are required.

c. 0402 (01005) compatible feeders are required.