00192377-02.pdf - 第107页
SIPLACE S-23 HM 2 Retrofitting Instruct. S-23 HM to SW V 502.xx incl. RV6-DLM 1 Head (Option) 07/01 Issue 2.9 Sequence: Software Upgrade on the Station Computer 107 2.9 Sequence: Software Upgrade on the St ation Computer…
2 Retrofitting Instruct. S-23 HM to SW V 502.xx incl. RV6-DLM1 Head (Option) SIPLACE S-23 HM
2.8 Sequence: Modifying Hardware 07/01 Issue
106
DANGER
Do not use alcohol for any cleaning work near open flame! 2
Å On the machine frame, degrease the area on which the 2 mounting pedestasl will be installed
(position, see: Fig. 2.8.22). Install the mounting pedestals.
Å Run the cable and the pneumatic hose and put on the cable ties (see: Fig. 2.8.22).
Å Remove all tools, etc., from the machine’s working area and close the doors of the machine
frame.
SIPLACE S-23 HM 2 Retrofitting Instruct. S-23 HM to SW V 502.xx incl. RV6-DLM1 Head (Option)
07/01 Issue 2.9 Sequence: Software Upgrade on the Station Computer
107
2.9 Sequence: Software Upgrade on the Station
Computer
This work can only be carried out after the hardware has been completely upgraded (see Section
2.8). You will need the following documentation: 2
– Software Version Description for Station V 502.01, Item no. 00192395-01 (German + English)
– Software Guide SITEST V 502.xx, Item no. 00192656-01 (English)
– Technical Information No. 34V05060 (operation of the CAN software)
The "scope of delivery" of the V 502.xx software for the station and line computers can be found
in the appropriate Software Version Description.
You will need: 1 CD with the Software SIPLACE Station 502/1 (502.01), Item no. 00358514-01.
DANGER
Pay close attention to the safety information for the SITEST program as described in Section 2.4.
When using the SITEST program, you are not only exposed to the normal increased risk of
accident, but also to added risk from the blades of the cutter.
The cutter and the empty tape duct must always be mounted completely.
The MTC and the component changeover table must always be docked correctly. 2
2.9.1 Checking the Firmware for Conveyor Control
You should carry out this check BEFORE installing the V 502.01 software on the station as follows: 2
Å Switch on the station:
– After approximately one minute the green "RUN" LED on the TSP210 conveyor controller
will flash = OK.
– If the red "FAIL" LED starts to flash -> load firmware with boot disk.
2.9.2 Installing the Touch Screen
NOTE:
The disk 1/1 02/99 supplied with the retrofit kit will not be required as the software for the Elo-
Touch Screen is available on the V 502.01 installation CD. 2
2 Retrofitting Instruct. S-23 HM to SW V 502.xx incl. RV6-DLM1 Head (Option) SIPLACE S-23 HM
2.9 Sequence: Software Upgrade on the Station Computer 07/01 Issue
108
Å Log in as the administrator.
Å Set the screen resolution for the 15" monitor (for detailed information see the Software Version
Description):
Properties -> Settings -> Desktop Area 1024 - 768 -> Settings: Refresh Frequency 75 Hz
Color Palette 65536 -> Small Fonts.
Å The software for the touch screen is available on the installation CD (the disk from the retrofit
kit is not required) and is installed during the software installation process.
The touch screen may also be installed with the Microtouch Setup program on the installation
CD (directory: D:\Siplace\Micro..\Disk1\setup... ; use Express setup).
Å To accept the settings, shut down and then restart.
2.9.3 Firmware Upgrade
Carry out the upgrade according to the Software Version Description as of V502.01.
Note the following additional information. 2
2.9.3.1 General
There are two directories under C:\SR: The current versions (and only these !) of each firmware
are saved in the directory CanFw. The version is queried using the "Check firmware" function in
SITEST and can then be downloaded in this window. When a new version is downloaded, this
version is copied to the "CanFw" directory and displayed under firmware "check" function as the
current version in SITEST.
The CanFwPool directory contains all the firmware versions ever copied to the station computer.
These versions can only be downloaded in the windows of the relevant modules, for example,
the conveyor controller.
The icons of the function "Check firmware" have the following meanings:
- Red cross: Download is not possible, for example, due to wrong BIOS on
the module.
- Green tick: Firmware is available and has already been downloaded
- Yellow exclamation mark: Firmware is available, but is still to be downloaded;
Do this using the "Download" button in
this window. All versions with the exclamation mark
will then be processed.
NOTE: This only applies to applications; the BIOS firmware
versions must be downloaded individually -> select
additional tabs.