00192377-02.pdf - 第93页

SIPLACE S-23 HM 2 Retrofitting Instruct. S-23 HM to SW V 502.xx incl. RV6-DLM 1 Head (Option) 07/01 Issue 2.8 Sequence: Modifying H ardware 93 2 Fig. 2.8.14 De-installation 12-Segment Rev . Head: Detaching Pneumatic Hose…

2 Retrofitting Instruct. S-23 HM to SW V 502.xx incl. RV6-DLM1 Head (Option) SIPLACE S-23 HM

2.8 Sequence: Modifying Hardware 07/01 Issue

Fig. 2.8.13 Undoing Screws Fastening Cable Harness; Undoing Connections on Conversion Board

Å Undo the screw fastening the cable clamp that holds the cable harness running downward

(see: arrow, Fig. 2.8.13, 1 socket hex head cap screw M3).

SIPLACE S-23 HM 2 Retrofitting Instruct. S-23 HM to SW V 502.xx incl. RV6-DLM1 Head (Option)

07/01 Issue 2.8 Sequence: Modifying Hardware

Fig. 2.8.14 De-installation 12-Segment Rev. Head: Detaching Pneumatic Hoses from Vacuum Generator

Key:

1. Compressed air feeder to the vacuum generator (5 hoses)

2. Collar on compressed air connection to the blast unit (support while pulling hoses off).

3. Cover over vacuum distributor board

(Fasteners: 2 socket hex head cap screws M2.5)

4. Ribbon cable: Connection on vacuum distributor board

Å Pull off the 5 compressed air hoses on the vacuum generator (see: Fig. 2.8.14).

Support in the case of the quick-release coupling (-> 2).

Å Remove the cover from the vacuum distributor board (loosen 2 socket hex head cap screws

M2.5, size 3).

Å Pull the 2 silicone hoses off the vacuum distributor board.

Å Pull the 2 silicone hoses off the silencer.

Å Support the placement head:

Undo the screws fastening the placement head: 3 socket hex head cap screws M4.

The head is still held in position by pins.

Å Pull the placement head (pins in the part to be pulled off) off the back part and set it down such

that it is not damaged, preferably in the proper package.

2 Retrofitting Instruct. S-23 HM to SW V 502.xx incl. RV6-DLM1 Head (Option) SIPLACE S-23 HM

2.8 Sequence: Modifying Hardware 07/01 Issue

2.8.7.2 Preparing the New 6-Segment Revolver Head (RV6-DLM1)

Fig. 2.8.15 New Placement Head: Mounting 3 Extensions (Steel Tubes), BOTTOM

Key:

1. Vacuum generator with silencer (fasteners: 4 socket hex head cap screws M4)

2. Silicone hoses am the vacuum distributor

3. NEW extension to be installed:

2 tubes 35 mm long (enclosed package in the retrofit kit, see: Section 2.5)

4. NEW extension to be installed:

1 tube 30 mm long (enclosed package in the retrofit kit, see: Section 2.5)

5. Vacuum feeders to the star (metal tube, fixed).

6. Vacuum hose, fastened with round-cable clamp (vacuum check for holding circuit).

Å Take the 6-Segment revolver head (DLM1) out of the retrofit kit.

Å Pull the silicone hoses of the vacuum generator and the vacuum board off the new placement

head.

Å Remove the vacuum generator incl. silencer from the new placement head so that you can

mount the metal-rubber vibration dampers from the enclosure pack later:

Undo 4 socket hex head cap screws M4 (see: and Fig. 2.8.16 and Fig. 2.8.18).