00192377-02.pdf - 第77页

SIPLACE S-23 HM 2 Retrofitting Instruct. S-23 HM to SW V 502.xx incl. RV6-DLM 1 Head (Option) 07/01 Issue 2.7 Required Document s 77 2.7 Required Document s – Software V er sion Descrip tion for S tation V 502.01, Item n…

2 Retrofitting Instruct. S-23 HM to SW V 502.xx incl. RV6-DLM1 Head (Option) SIPLACE S-23 HM

2.6 Required Tools, Auxiliary Test Equipment, etc. 07/01 Issue

2.5.8 Nozzle Changer for 6-segment revolver head (option)

– Nozzle Changer for 6-segment revolver head (option), Item no. 00116162-01

2.5.9 Software LR UNIX, V 502.01

NOTE:

The line computer software V 502.01 is always required for this upgrade -> Item no.: see below.

Use the Software Version Description LRU V 502.01 for the installation. It also contains the re-

quirements for the UNIX line computer. 2

– Software LR UNIX V502.01: Booting and installation disk and CD, Item no. 00358516-01.

2.6 Required Tools, Auxiliary Test Equipment, etc.

– Set of Allen-type wrenches

– Cross-slotted screwdriver, size 1

– Screwdriver with internal serrations T8

– Oblique-nosed cutting pliers (for removing cable ties while de-installing nozzle changer RV12)

– Clean cloth and ethyl alcohol

– CAN terminal with ribbon cable

– Precision calibration case

– Components for precision calibration

– Mapping plates for PCB and revolver mapping

- 4 Cable ties (W = 2.4 mm, L = 92 mm) 00805140-01 per nozzle changer

- 2 Mounting pedestals for cable ties,

adhesive 00318666-01 per nozzle changer

- 1 (if necessary) adhesive label (with text) 00332920-03 German and English

- 1 (if necessary) adhesive label (with text) at request EU languages

- 1 (if necessary) adhesive label:

triangular warning

symbol, "Hand injury" 00335957-01

SIPLACE S-23 HM 2 Retrofitting Instruct. S-23 HM to SW V 502.xx incl. RV6-DLM1 Head (Option)

07/01 Issue 2.7 Required Documents

2.7 Required Documents

– Software Version Description for Station V 502.01, Item no. 00192395-01 (G + E)

– Software Guide SITEST V 502.xx, Item no. 00192656-01 (E)

– Software version description, LRU V 502.01, Item no. 00192397-01 (G + E)

– Technical Information No. 34V05060 *)

– For the installation of options in connection with upgrading:

– 6-segment revolver head, modular:

Conversion instructions DLM1 Collect & Place head, Item no. 00191684-03 (G + E).

– Setting instructions for SIPLACE S-25 HM, Item no. 00192192-02 (G + E)

– Retrofitting instructions for MTC on S-25 HM, Item no. 00192792-02 (G + E)

– Retrofitting instructions "Head board, modular, Item no. 00192919-01 (G + E) -> in

progress,

Partial information, e. g., photos, Item nos. PCBs

, new cables required, etc. -> see: retro-

fitting instructions "PCB camera Multicolor..." (below)

– Retrofitting instructions

"PCB camera Multicolor on S-25 HM and HS-50", Item no. 00192232-01 (G + E);

-> Requirement: Retrofitting of the modular head boards at both gantries.

*) ATTENTION: This documentation is intended for INTERNAL use only.

When finished, put the documentation back with your papers.

NOTE:

These instructions contain the retrofitting of the nozzle changer RV6 Standard (for 6-segment re-

volver head DLM1) (see: Section 2.8.8). 2

2 Retrofitting Instruct. S-23 HM to SW V 502.xx incl. RV6-DLM1 Head (Option) SIPLACE S-23 HM

2.8 Sequence: Modifying Hardware 07/01 Issue

2.8 Sequence: Modifying Hardware

2.8.1 De-installing the Touch-Screen Driver

Å Your first step should be to de-install the old touch-screen driver as follows:

Settings -> System control -> Software -> "Monitor-Mice" -> Remove.

2.8.2 Preparatory Steps

Å Push the gantry/placement head into the area over the PCB conveyor.

The function for changing the component table - "All gantires in set-up position" - exists only

with Version 502.01 and later).

Å Undock the movable component changeover table from the machine and move it out of the

machine.

Å Turn the machine OFF; isolate it from the mains; turn the compressed air OFF at the com-

pressed air unit and bleed the needle valve on the compressed air unit (see DANGER text in

Section 2.4).

2.8.3 Installing the Conveyor Control TSP 210 and the I/O Boards KSP 219

DANGER

Comply with the safety notes in Section 2.4.

Comply with DIN EN 60204 during all work inside the machine frame. 2

Described below is the exchange of the I/O boards KSP-P218-A32 by the I/O subsystem consist-

ing of the assemblies:

– KSP-P219-A32 (I/O board),

– TSP-210 (conveyor control) and

– Backplane P219

You will need:

Conversion kit "URS S23HM auf SW502 incl. head, modular", Item no. 00356654-01

Å Open the folding doors of the machine frame at the control unit/terminal panel, left board slot.