00192377-02.pdf - 第108页
2 Retrofitting Instruct. S-23 HM t o SW V 502. xx incl. RV 6-DLM1 Head (O ption) SIPLACE S -23 HM 2.9 Sequence: Software Upgrade on the Station Computer 07/01 Issue 108 Å Log in as the admin istrator. Å Se t the screen r…
SIPLACE S-23 HM 2 Retrofitting Instruct. S-23 HM to SW V 502.xx incl. RV6-DLM1 Head (Option)
07/01 Issue 2.9 Sequence: Software Upgrade on the Station Computer
107
2.9 Sequence: Software Upgrade on the Station
Computer
This work can only be carried out after the hardware has been completely upgraded (see Section
2.8). You will need the following documentation: 2
– Software Version Description for Station V 502.01, Item no. 00192395-01 (German + English)
– Software Guide SITEST V 502.xx, Item no. 00192656-01 (English)
– Technical Information No. 34V05060 (operation of the CAN software)
The "scope of delivery" of the V 502.xx software for the station and line computers can be found
in the appropriate Software Version Description.
You will need: 1 CD with the Software SIPLACE Station 502/1 (502.01), Item no. 00358514-01.
DANGER
Pay close attention to the safety information for the SITEST program as described in Section 2.4.
When using the SITEST program, you are not only exposed to the normal increased risk of
accident, but also to added risk from the blades of the cutter.
The cutter and the empty tape duct must always be mounted completely.
The MTC and the component changeover table must always be docked correctly. 2
2.9.1 Checking the Firmware for Conveyor Control
You should carry out this check BEFORE installing the V 502.01 software on the station as follows: 2
Å Switch on the station:
– After approximately one minute the green "RUN" LED on the TSP210 conveyor controller
will flash = OK.
– If the red "FAIL" LED starts to flash -> load firmware with boot disk.
2.9.2 Installing the Touch Screen
NOTE:
The disk 1/1 02/99 supplied with the retrofit kit will not be required as the software for the Elo-
Touch Screen is available on the V 502.01 installation CD. 2
2 Retrofitting Instruct. S-23 HM to SW V 502.xx incl. RV6-DLM1 Head (Option) SIPLACE S-23 HM
2.9 Sequence: Software Upgrade on the Station Computer 07/01 Issue
108
Å Log in as the administrator.
Å Set the screen resolution for the 15" monitor (for detailed information see the Software Version
Description):
Properties -> Settings -> Desktop Area 1024 - 768 -> Settings: Refresh Frequency 75 Hz
Color Palette 65536 -> Small Fonts.
Å The software for the touch screen is available on the installation CD (the disk from the retrofit
kit is not required) and is installed during the software installation process.
The touch screen may also be installed with the Microtouch Setup program on the installation
CD (directory: D:\Siplace\Micro..\Disk1\setup... ; use Express setup).
Å To accept the settings, shut down and then restart.
2.9.3 Firmware Upgrade
Carry out the upgrade according to the Software Version Description as of V502.01.
Note the following additional information. 2
2.9.3.1 General
There are two directories under C:\SR: The current versions (and only these !) of each firmware
are saved in the directory CanFw. The version is queried using the "Check firmware" function in
SITEST and can then be downloaded in this window. When a new version is downloaded, this
version is copied to the "CanFw" directory and displayed under firmware "check" function as the
current version in SITEST.
The CanFwPool directory contains all the firmware versions ever copied to the station computer.
These versions can only be downloaded in the windows of the relevant modules, for example,
the conveyor controller.
The icons of the function "Check firmware" have the following meanings:
- Red cross: Download is not possible, for example, due to wrong BIOS on
the module.
- Green tick: Firmware is available and has already been downloaded
- Yellow exclamation mark: Firmware is available, but is still to be downloaded;
Do this using the "Download" button in
this window. All versions with the exclamation mark
will then be processed.
NOTE: This only applies to applications; the BIOS firmware
versions must be downloaded individually -> select
additional tabs.
SIPLACE S-23 HM 2 Retrofitting Instruct. S-23 HM to SW V 502.xx incl. RV6-DLM1 Head (Option)
07/01 Issue 2.9 Sequence: Software Upgrade on the Station Computer
109
2.9.3.2 Conveyor Controller TSP210
Å If no firmware is available on the built-in conveyor controller:
BEFORE installing the station software, you should install the firmware for the TSP 120
conveyor controller (boot disk in MC).
Reason: If the station software is installed first, CAN bus errors may occur during the ICOS
download which could interfere with the download.
Procedure:
– Read the new transport software on to the MC:
The winimage file is located on the station software CD in the directory:
\Siplace\Sip_mc\HS-50\Fd_image.TRP\TSP_S25
The disk is bootable.
The installation process runs automatically.
Å Always check the current BIOS firmware version using SITEST (individual download) and
reload it if necessary.
2.9.3.3 Axis Control Card (Type KSP-362; as for S-23 and HS-50)
Requires: 2
– Technical Information 34V5060, for operating the CAN software.
– Laptop (CAN terminal)
Å Check: If a BIOS version lower than 0207 is installed on the axis control card, then a BIOS
version 0207 or higher must be installed with a laptop (CAN terminal).
-> The laptop is connected to the CAN bus using a ribbon cable.
Å Using the CAN terminal, first read in the new BIOS (file: A0100207.hex) and then the new
firmware.
Help on using the CAN software can be found in the Technical Information mentioned
above.
Å CAUTION:
- Switch the CAN network 1 over to 1Mbit!
- Only select the existing axes, i.e. Gantry 1 and 2 and the two free axes.
Å CAUTION:
As of version 0207 or higher, the axis control cards can always be downloaded. This means
that you can then load the application (4.01) in SITEST or with the laptop.
The current version is located on the installation CD and is installed on the station computer
automatically.
Å After the software has been installed, you MUST use the "Check Firmware" function in SITEST
to check the current version (see below, Section 2.9.4).