00192377-02.pdf - 第116页
2 Retrofitting Instruct. S-23 HM t o SW V 502. xx incl. RV 6-DLM1 Head (O ption) SIPLACE S -23 HM 2.11 Setting the Dynamic s 07/01 Issue 116 2.1 1 Setting the Dynamics CAUTION After excha nging a pl aceme nt head the set…
SIPLACE S-23 HM 2 Retrofitting Instruct. S-23 HM to SW V 502.xx incl. RV6-DLM1 Head (Option)
07/01 Issue 2.10 SITEST: Adjust Configuration, Entry Zero Point Compens. Values RV6 Head
115
Å If further options were installed during the upgrading process, configure them in accordance
with the relevant retrofitting instructions (Item no. see: Section 2.7).
2.10.5 Configuration of Interface
The "Conveyor interface" SMEMA or SIEMENS interface can be selected in the software
V 502.01, however the setting must always be SIEMENS because the interface signals on these
machines, S-23 HM / S-25 HM, are always converted entirely on the SMEMA assembly. 2
-> A change will evoke an error message! 2
2.10.6 Concluding Acceptance of the Configuration
Å After completely adjusting the machine configuration:
Exit the menu "Machine Configuration" by pressing "Accept" (button).
The main view will be displayed and the messsage will appear:
The machine configuration has changed.
Shut down -> Restart machine -> Click on "OK" (button)
Å Boot up the machine and change back to the SITEST program.
2.10.7 Entry for the Zero Point Compensation Values of the New Placement Head
Å AFTER the restart, transfer the zero point compensation values on the label of the place-
ment head just installed (visible in assembled condition).
Å For the entry, select the menu "Head exchange" in the SITEST main view or select:
-> ICON "Axis functions of the revolver head" -> Activate the relevant axis (z-, star, dp) by
clicking on the radio button -> Click on "Positions" (button).
Å Select "Zero point compensation" -> Edit -> Transfer the value from the label -> Click on
"Accept" (button)
Å Carry out the transfer of the remaining zero point compensations from the label in the same
manner.
Å Now carry out the overall reference run (button).
2 Retrofitting Instruct. S-23 HM to SW V 502.xx incl. RV6-DLM1 Head (Option) SIPLACE S-23 HM
2.11 Setting the Dynamics 07/01 Issue
116
2.11 Setting the Dynamics
CAUTION
After exchanging a placement head the setting of the dynamics must always be checked.
When changing from the 12- to the 6-segment head (optional) in particular, the Z-axis is much too
fast and the P-component much too low.
It is IMPERATIVE that the dynamics be set.
In addition, when the modular head board (optional) is installed, the track signals must also be
calibrated. 2
Å For the new 6-segment revolver head, modular, calibrate the Z-axis and the dp-axis.
To do so, proceed according to the setting instructions in SITEST -> Help -> Setting of
dynamics or according to the setting instructions (Item no. see: Section 2.7).
2.12 Calibrating the Placement Heads and Cameras
Requirements:
– The dynamics must be set.
– To use the final operating conditions as a basis, we recommend that the protective covers of
both placement heads be mounted first.
NOTE:
If errors occur during the calibration, you may be using the incorrect axis data.
Consequence: During calibration, the part to be calibrated is only turned 45° or the machine’s zero
point is incorrect (by 5 mm or a multiple thereof).
If an error occurs, change the configuration back to the 12-segment head and then back to the
6-nozzle head. 2
ÅCalibrate the "Placement heads and cameras" as described in the Software Guide
SITEST V 502.xx.
This calibration is a prerequisite for measuring the nozzle changer.
2
SIPLACE S-23 HM 2 Retrofitting Instruct. S-23 HM to SW V 502.xx incl. RV6-DLM1 Head (Option)
07/01 Issue 2.13 Loading and Calibrating SITEST Nozzle Changer RV6 Standard with Nozzles
117
2.13 Loading and Calibrating SITEST Nozzle Changer
RV6 Standard with Nozzles
NOTE:
In SITEST V 502.01 the nozzles on the head and in the nozzle changer are now monitored, as is
the case with the station software.
For the nozzle changer MTC, proceed as described in "Retrofitting instructions MTC on S-25 HM"
(see: Section 2.7). 2
Requirements:
– The new placement head(s) DLM1 (6-segment) and the nozzle changer(s) RV6 Standard
must be configured (see: Section 2.10).
– All placement heads and cameras must have been calibrated already (see: Section 2.12).
2.13.1 Loading with Nozzles
Å
Starting from the SITEST main view, select
the ICON "Revolver heads" -> and
then "Revolver head 1" or "Revolver head 2" .
Å In the menu "Functions", click on the ICON "Nozzle changer head functions" .
The following will appear on the screen: