presto_en.pdf - 第10页
Page 10 1 Introduction This manu al describes PRESTO, a USB program mer and its control software, both manufactured b y A SIX. Chapter 1 gives you ‘quick start’ instruct ions on how t o start working with th e programmer…
Page 10
1
Introduction
This manual describes PRESTO, a USB programmer and
its control software, both manufactured by ASIX.
Chapter 1 gives you ‘quick start’ instructions on how to
start working with the programmer, offers examples of its
connecting to applications and provides technical
specifications.
Chapter 2 focuses on the installation of drivers and
software updates.
Chapter 3 introduces the UP program, which is software
used for controlling all ASIX programmers. You can find
procedures there for setting up the programmer prior to
programming, for actual programming and/or verification
of devices. It also describes how to control the software
from a command line or a DLL library.
Chapter 4 presents the JTAG SVF Player software used for
programming devices with the JTAG interface using .svf/
.xsvf files.
Chapter 5 offers tips and tricks in case of experiencing
difficulties with programming.
Abbreviations & Terms Used
HVP (High Voltage Programming) is a
programming mode in which a higher
voltage than the power-supply voltage is
applied to pin P in the initial phase.
ICSP (In-Circuit Serial Programming). The
meaning of ICSP is identical with the
meaning of ISP (In System Programming) in
this manual, i.e. device programming done
inside a system.
LVP (Low Voltage Programming) is a
programming mode in which none of the
pins has higher than the power-supply
voltage applied.
PDI Program and Debug Interface
SBW (SPY-BI-WIRE) MSP430 microcontroller
interface
TPI Atmel Tiny Programming Interface
VCC If the text features VCC or VDD, they mean
the power-supply voltage on the VDD pin,
which can serve as either input or output
depending on the particular application.
VPP If the text features VPP, it means the
programming voltage on pin P of devices
with High Voltage Programming.
The term “file” means a file with data to be programmed
in context of this manual, in other cases a particular type
of file is specified.
A file with .hex extension means Intel-HEX file whilst a file
with .bin extension means binary file.
Page 11
2
PRESTO
Thank you for buying the PRESTO programmer made by
ASIXs.r.o. It was a wise decision. Feel free to contact our
technical support in case of any questions or doubts.
2.1
Package Content
Your PRESTO package should include:
• PRESTO programmer
• ICSPCAB8 cable
• USB cable (type A - B)
• Info leaflet
2.2
Features
PRESTO is a fast USB In-System programmer suitable for
programming a range of devices such as microcontrollers,
EEPROM or Flash serial memory chips, CPLD, FPGA and
many others.
• USB1.1 (USB2.0 compatible) interface, programmer
powered via USB
• 3MHz in/out
• synchronous programming, JTAG support
• programming voltage from 2.7V to 5.5V
• feeds applications with 5V
• overcurrent protection on VDD and VPP sources
• overvoltage protection on VDD pin
• GO button for quick function selection
• more than one simultaneously running programmer
per PC, command line support, support for Windows
messages and for DLL
• WindowsXP or later
• compact
2.3
Quick Start
Please install the drivers and the UP software prior to the
first use of PRESTO.
2.3.1 Windows
Administrator rights are required to run the software
for the first time.
Start with installing the UP program. Its installer installs
the USB driver for PRESTO, too. You can download the
installer from
www.asix.tech/prg_up_en.html.
Once the installation is complete, connect the PRESTO
programmer to your computer.
The driver contained in the UP installer is intended for
Windows 7 and later. For older Windows operating system
versions the driver has to be downloaded from
www.asix.net, from download section of the programmer
and unpacked somewhere. After the programmer has
been connected, the operating system asks for the driver.
In "Found New Hardware" dialog the path to the
unpacked driver has to be set.
The green ON-LINE LED should turn on after a few
moments and the Windows Device Manager should
present the programmer as correctly installed.