presto_en.pdf - 第76页

Page 76 0 Lower Boot alias 1 Boot Flash 1 and 2 SpecSettings.PREST.PSoCAlg integer 0 automat ic selection 1 assume VDD > 3.6V 2 assume VDD =< 3.6V SpecSettings.PREST.PSoCRSTInit integer 0 Reset mode 1 Power cycli…

100%1 / 101
Page 75
Serial.Succ.AfterProg
boolean
If true, next serial number is generated after successful
programming.
Serial.LogSN
boolean
If true, the result of programming is logged to a selected
file.
Serial.LogFile
string
File name of a file where the result of the programming
will be logged.
ICSP.LongTime
boolean
If true, longer times for switching Vcc are taken.
ICSP.LongTime.Time.SwOn
integer
Time to wait after Vcc is switched on in microseconds.
ICSP.LongTime.Time.SwOff
integer
Time to wait after Vcc is switched off in microseconds.
SpecSettings.PREST.Power
integer
0 idle power supply is None / External
1 idle power supply is Internal 5V
SpecSettings.PREST.ProgPower
integer
0 power supply during programming is
External 2.7 to 5.5V
1 power supply during programming is
Internal 5V
SpecSettings.PREST.i2cSpeed
integer
0 100kHz
1 500kHz
2 1MHz
3 Maximal
SpecSettings.PREST.i2cAddr
integer
0 first suitable address or N/A
1 second suitable address
etc...
SpecSettings.PREST.LVP
integer
0 HVP method
1 LVP method
SpecSettings.PREST.PICAlg
integer
0 automatic selection
1 assume VDD = 5V
2 assume VDD < 5V
SpecSettings.PREST.UsePE
boolean
If true, PE (programming executive) is used for
programming of PIC MCUs.
SpecSettings.PREST.PIC32MZ_BootProg
integer
Page 76
0 Lower Boot alias
1 Boot Flash 1 and 2
SpecSettings.PREST.PSoCAlg
integer
0 automatic selection
1 assume VDD > 3.6V
2 assume VDD =< 3.6V
SpecSettings.PREST.PSoCRSTInit
integer
0 Reset mode
1 Power cycling
SpecSettings.PREST.MSP430osc
integer
0 Calibrated internal RC oscilator
1 Not calibrated internal RC oscilator
SpecSettings.PREST.MSP430speed
integer
0 Normal
1 Slow
2 Slowest
SpecSettings.PREST.MSP430EraseSegme
ntA
boolean
If true, MSP430 Segment A is erased.
SpecSettings.PREST.SPI_Flash_Freq
integer
0 3MHz
1 1.5MHz
2 750kHz
SpecSettings.PREST.AVRXTAL.CLK
SpecSettings.PREST.AVRXTAL.RPT
integers
represent maximum AVR oscillator frequency
values can be found in *.lng files at item
MainForm.PRESTSpecForm.ComboAVRXTAL.xxx.Items
where xxx is minimum divisor of system clock of selected
AVR's SPI module. This is 2 for new AVRs, 3 and 4 for
older AVRs and 24 for Atmel's 8051 arch. processors.
These settings can be found in ini file too at
[SpecSettings.PREST], XTALRpt and XTALClk.
SpecSettings.PREST.AVRXTAL.AutoClk
boolean
If true, faster programming with slow clock is used for
AVR MCUs.
SpecSettings.PREST.AVRRSTInverse
boolean
If true, the reset signal polarity is assumed to be inverse
in comparison with standard polarity of the reset signal of
the selected chip. It is supported with AVR and 8051
devices.
SpecSettings.PREST.AVRHVP
boolean
If true, high voltage method is used for AVR MCUs, it is
supported for AVR TPI interface only.
SpecSettings.FORTE.UVCCLevel
integer
Defines the size of the internal supply voltage provided by
Page 77
FORTE programmer. The value is in voltsx10.
SpecSettings.FORTE.Power
boolean
If true, idle power supply is provided by FORTE
programmer.
SpecSettings.FORTE.ProgPower
boolean
If true, the supply voltage during programming is
provided by FORTE programmer.
SpecSettings.FORTE.LVP
integer
0 HVP method
1 LVP method
SpecSettings.FORTE.UsePE
boolean
If true, PE (programming executive) is used for
programming of PIC MCUs, when programmed by FORTE
programmer.
SpecSettings.FORTE.PIC32MZ_BootProg
integer
0 Lower Boot alias
1 Boot Flash 1 and 2
SpecSettings.FORTE.PSoCAlg
integer
0 automatic selection
1 assume VDD > 3.6V
2 assume VDD =< 3.6V
SpecSettings.FORTE.PSoCRSTInit
integer
0 Reset mode
1 Power cycling
SpecSettings.FORTE.MSP430osc
integer
0 Calibrated internal RC oscilator
1 Not calibrated internal RC oscilator
SpecSettings.FORTE.MSP430speed
integer
0 Normal
1 Slow
2 Slowest
SpecSettings.FORTE.MSP430EraseSegme
ntA
boolean
If true, MSP430 Segment A is erased.
SpecSettings.FORTE.MSP430Interface
integer
0 JTAG
1 SBW
SpecSettings.FORTE.ARMFreq
integer
The value specifies the frequency of connected oscillator
or crystal. This value is used for programming of
ARM7TDMI.
SpecSettings.FORTE.ARMOscType
integer
0 Crystal
1 Ext. Clock