presto_en.pdf - 第77页

Page 77 FORTE programmer. The value is in voltsx10. SpecSettings.FORT E.Power boolean If true, idle p ower sup ply is provided by FORT E programmer. SpecSettings.FORT E.ProgPower boolean If t rue, t he supply voltage d…

100%1 / 101
Page 76
0 Lower Boot alias
1 Boot Flash 1 and 2
SpecSettings.PREST.PSoCAlg
integer
0 automatic selection
1 assume VDD > 3.6V
2 assume VDD =< 3.6V
SpecSettings.PREST.PSoCRSTInit
integer
0 Reset mode
1 Power cycling
SpecSettings.PREST.MSP430osc
integer
0 Calibrated internal RC oscilator
1 Not calibrated internal RC oscilator
SpecSettings.PREST.MSP430speed
integer
0 Normal
1 Slow
2 Slowest
SpecSettings.PREST.MSP430EraseSegme
ntA
boolean
If true, MSP430 Segment A is erased.
SpecSettings.PREST.SPI_Flash_Freq
integer
0 3MHz
1 1.5MHz
2 750kHz
SpecSettings.PREST.AVRXTAL.CLK
SpecSettings.PREST.AVRXTAL.RPT
integers
represent maximum AVR oscillator frequency
values can be found in *.lng files at item
MainForm.PRESTSpecForm.ComboAVRXTAL.xxx.Items
where xxx is minimum divisor of system clock of selected
AVR's SPI module. This is 2 for new AVRs, 3 and 4 for
older AVRs and 24 for Atmel's 8051 arch. processors.
These settings can be found in ini file too at
[SpecSettings.PREST], XTALRpt and XTALClk.
SpecSettings.PREST.AVRXTAL.AutoClk
boolean
If true, faster programming with slow clock is used for
AVR MCUs.
SpecSettings.PREST.AVRRSTInverse
boolean
If true, the reset signal polarity is assumed to be inverse
in comparison with standard polarity of the reset signal of
the selected chip. It is supported with AVR and 8051
devices.
SpecSettings.PREST.AVRHVP
boolean
If true, high voltage method is used for AVR MCUs, it is
supported for AVR TPI interface only.
SpecSettings.FORTE.UVCCLevel
integer
Defines the size of the internal supply voltage provided by
Page 77
FORTE programmer. The value is in voltsx10.
SpecSettings.FORTE.Power
boolean
If true, idle power supply is provided by FORTE
programmer.
SpecSettings.FORTE.ProgPower
boolean
If true, the supply voltage during programming is
provided by FORTE programmer.
SpecSettings.FORTE.LVP
integer
0 HVP method
1 LVP method
SpecSettings.FORTE.UsePE
boolean
If true, PE (programming executive) is used for
programming of PIC MCUs, when programmed by FORTE
programmer.
SpecSettings.FORTE.PIC32MZ_BootProg
integer
0 Lower Boot alias
1 Boot Flash 1 and 2
SpecSettings.FORTE.PSoCAlg
integer
0 automatic selection
1 assume VDD > 3.6V
2 assume VDD =< 3.6V
SpecSettings.FORTE.PSoCRSTInit
integer
0 Reset mode
1 Power cycling
SpecSettings.FORTE.MSP430osc
integer
0 Calibrated internal RC oscilator
1 Not calibrated internal RC oscilator
SpecSettings.FORTE.MSP430speed
integer
0 Normal
1 Slow
2 Slowest
SpecSettings.FORTE.MSP430EraseSegme
ntA
boolean
If true, MSP430 Segment A is erased.
SpecSettings.FORTE.MSP430Interface
integer
0 JTAG
1 SBW
SpecSettings.FORTE.ARMFreq
integer
The value specifies the frequency of connected oscillator
or crystal. This value is used for programming of
ARM7TDMI.
SpecSettings.FORTE.ARMOscType
integer
0 Crystal
1 Ext. Clock
Page 78
2 Int.RC 32kHz
SpecSettings.FORTE.ARMCommFreq
integer
Selects communication frequency between FORTE
programmer and the programmed chip. The frequencies
are same as stated in the "Communication frequency"
ComboBox in UP. 0 means the highest frequency, 1 is
lower and so on.
SpecSettings.FORTE.SPI_Flash_Freq
integer
Selects communication frequency between FORTE
programmer and the programmed chip. The frequencies
are same as stated in the "Communication frequency"
ComboBox in UP. 0 means the highest frequency, 1 is
lower and so on.
SpecSettings.FORTE.AVRXTAL.DELAY
integer
represents maximum AVR oscillator frequency
value can be found in *.lng files at item
MainForm.PRESTSpecForm.ComboAVRXTALPresto2.xxx.It
ems where xxx is minimum divisor of system clock of
selected AVR's SPI module. This is 2 for new AVRs, 3 and
4 for older AVRs and 24 for Atmel's 8051 arch.
processors.
This setting can be found in ini file too at
[SpecSettings.FORTE], XTALClk.
SpecSettings.FORTE.AVRXTAL.AutoClk
boolean
If true, faster programming with slow clock is used for
AVR MCUs.
SpecSettings.FORTE.AVRRSTInverse
boolean
If true, the reset signal polarity is assumed to be inverse
in comparison with standard polarity of the reset signal of
the selected chip. It is supported with AVR and 8051
devices.
SpecSettings.FORTE.AVRHVP
boolean
If true, high voltage method is used for AVR MCUs, it is
supported for AVR TPI interface only.
SpecSettings.FORTE.ATxmegaInterface
integer
0 PDI
1 JTAG
SpecSettings.FORTE.i2cSpeed
integer
0 100kHz
1 400kHz
2 1MHz
3 Maximal
SpecSettings.FORTE.i2cAddr
integer
0 first suitable address or N/A
1 second suitable address
etc...
5.13
Appendix B: Use of ICSP
ICSP (In-Circuit Serial Programming) is a method of PIC
microcontroller programming making it possible to
program devices already placed on PCBs.
Two different algorithms may be used for PIC
microcontroller programming: HVP (using programming