presto_en.pdf - 第47页
Page 47 ▸ Erase code/main memory A keyboard shortcu t can be assigned in O ptions ➙ Key shortcuts This co mmand erases the code/main memory. It canno t be used if C ode/Data Protect ion is active. ▸ Erase data memory A k…
Page 46
▸ Read data memory
A keyboard shortcut can be assigned in Options ➙ Key
shortcuts
This command reads the data (EEPROM) memory.
▸ Read configuration memory
A keyboard shortcut can be assigned in Options ➙ Key
shortcuts
This command reads the configuration memory and ID
positions (if device contains them).
▸ Read address
This function enables reading of data from user filled
address, it supports MCUs ARM via SWD interface.
Device ➙ Verify
Keyboard shortcut: Shift+F7
This command opens a sub-menu with device memory
content verification options. Some of them may be not
available for certain device types
▸ Verify all
Keyboard shortcut: F7
This command compares the content of all device
memories with the current content of HEX editors.
▸ Verify all except data memory
A keyboard shortcut can be assigned in Options ➙ Key
shortcuts
This command compares the content of all device
memories except its data memory with the current
content of HEX editors.
▸ Verify code/main memory
A keyboard shortcut can be assigned in Options ➙ Key
shortcuts
This command compares the content of the code/main
memory with the current content of code/main memory's
HEX editor.
▸ Verify data memory
A keyboard shortcut can be assigned in Options ➙ Key
shortcuts
This command compares the content of the data memory
with the current content of data memory's HEX editor.
▸ Verify configuration memory
A keyboard shortcut can be assigned in Options ➙ Key
shortcuts
This command compares the content of device's
configuration memory and ID positions (if device contains
them) with settings in the Configuration window.
Device ➙ Erase
Keyboard shortcut: Shift+F8
This command opens a sub-menu with device memory
erasing options.
Erasure verification (blank check) is automatically
performed after each erasing. This verification can be
skipped by choosing Options ➙ Program settings ➙
Programming ➙ Do not perform blank check after
erasing. This can save time with some devices.
▸ Erase all
Keyboard shortcut: F8
This command erases the whole device.
Page 47
▸ Erase code/main memory
A keyboard shortcut can be assigned in Options ➙ Key
shortcuts
This command erases the code/main memory. It cannot
be used if Code/Data Protection is active.
▸ Erase data memory
A keyboard shortcut can be assigned in Options ➙ Key
shortcuts
This command erases the data memory and verifies it. It
cannot be used if Code/Data Protection is active.
Device ➙ Blank check
Keyboard shortcut: Shift+F9
This command opens a sub-menu with device erasure
verification options. Some of them may be not available
for certain device types.
▸ Blank check all
Keyboard shortcut: F9
This command verifies whether the device is correctly
and completely erased.
▸ Blank check all except data memory
A keyboard shortcut can be assigned in Options ➙ Key
shortcuts
This command verifies whether the device except the
data memory has been correctly erased.
▸ Blank check of code/main memory
A keyboard shortcut can be assigned in Options ➙ Key
shortcuts
This command verifies whether the code/main memory is
correctly erased.
▸ Blank check of data memory
A keyboard shortcut can be assigned in Options ➙ Key
shortcuts
This command verifies whether the data memory is
correctly erased.
▸ Blank check of configuration memory
A keyboard shortcut can be assigned in Options ➙ Key
shortcuts
This command verifies whether the configuration memory
and ID positions (if device contains them) are correctly
erased.
Device ➙ Select device
Keyboard shortcut: F4
This dialog allows you to select a device type to be
programmed. Some memory types need to have their
data organization selected after the device type
selection.
Only devices supported by the currently selected
programmer are displayed in the dialog window. If you
want to select a device not supported by the current
programmer, select a different programmer type first.
For further information on selecting a device see
Device
Type Selection
.
Device ➙ Device info
Shows a window with information about connecting the
selected device to the programmer.
Page 48
Options Menu
Keyboard shortcut: Shift+F10
The Options menu holds all the possible settings of the
UP program. There is a great number of setting
parameters. If you are not sure that all settings are
correct, you may use the Load defaults button, which
returns all the settings to the initial (factory) state.
Advice
Program settings ➙ Load defaults button renews the state of
all settings on all tabs, i.e. even the color settings, for example.
Options ➙ Program settings ➙
Programming
Keyboard shortcut: Shift+F10
This tab provides for setting all the general programming
parameters.
Settings concerning the programmer and the
communication port are described in
Programmer
Selection
.
A special
Device ➙ Select device window is available for
setting the device type.
▸ Reload file before every programming
The program reads the current file with programming
data from the disc before each and every request to
program a device if this option is checked.
If the use of serial numbers is also activated requesting
reading the current file prior to programming, then the
file is read first and only then is the current serial number
written.
▸ Keep manually modified data
When this choice is active, the file load before
programming does not rewrite manually changed data.
This choice affects only behavior of the file reload before
programming.
▸ Warn before file load, when data in
some editor have been changed
When before load of the file before programming it is
found that data in some editor have been changed, the
program shows a warning.
▸ Warn, when the loaded file has not
changed
Program shows a warning, when the content of the
loaded file has not changed from the previous
programming.
▸ Program file locations only
The programming changes only the positions contained in
the file. First it reads the programmed device content,
then it reads the file content which replaces the data read
from the device. The addresses which are not contained
in the file hold the value read from the device. Finally the
memory is programmed.
▸ Ask before erasing
With this option checked, the program asks for user
confirmation before erasing a device.
▸ Ask before programming of OTP / Flash
/ Code/Data Protection / differential
A set of options determining which user confirmation
dialogs will or will not be displayed by the program.
The program asks just once except the Code/Data
Protection programming. If the program needs to ask
the user for additional information before actual
programming (such as Device has Code or Data
Protection. Do you want to erase it entirely?), it