00193922-01.pdf - 第260页
6 Component handling User Manual SIPLACE HF Series 6.3 Component trolley Software Version SR. 505.xx 05/2004 US Edition 260 Description of the modules 6 The chass is runs s moothly and is ea sy to man euver . The handl e…
User Manual SIPLACE HF Series 6 Component handling
Software Version SR.505.xx 05/2004 US Edition 6.3 Component trolley
259
6.3.1 Structure of the component trolley
The component trolley consists essentially of a chassis, a component feeder table on which the
feeder is mounted, a communication unit, a tape reel container and a waste container.
Fig. 6.3 - 3 Component trolley: Front and back view
(1) Chassis
(2) Component feeder table
(3) Communication unit
(4) Tape reel container
(5) Waste tape container
(6) Interface for the power module, communication and safety circuits
(7) Handle
(8) Pockets for set-up list print-outs
6 Component handling User Manual SIPLACE HF Series
6.3 Component trolley Software Version SR.505.xx 05/2004 US Edition
260
Description of the modules 6
The chassis runs smoothly and is easy to maneuver.
The handles (item 8) can be pulled out and locked at the required height.
On both sides of the chassis there are pockets for holding the set-up list print-outs. These lists can
also be removed from the pockets during the production process.
The component feeder table (item 2) has a capacity of up to 15 locations for 30 mm wide feeders.
The feeders are mechanically centered on the table with centering pins and balls. A separate com-
pressed air rail supplies the feeders with compressed air.
The interface for the power module, communication and safety circuits (item 6) is beneath the
component feeder table bed. The compressed air supply for bulk case feeders is also provided
via this interface.
NOTE ON OPERATIONAL SAFETY
All component trolleys or matrix tray changers must be docked on the machine in order to oper-
ate it. If they are not, the machine stays in EMERGENCY STOP status. The placement process
is interrupted.
The communication unit (item 3) sends the necessary voltages and control signals to the feeders.
In the standard version, the tape reel container (item 4) holds tape reels up to 17" (432 mm). The
pull-out waste tape container (item 5) can be found beneath the chassis. The cut waste tape travel
down a chute into the waste container, which must be regularly emptied.
6.3.2 Technical data
6
Length x width 633 x 592 mm²
Height
859 mm for 830 mm PCB transport height
929 mm for 900 mm PCB transport height
959 mm for 930 mm PCB transport height
979 mm for 950 mm PCB transport height
PCB transport height
830 mm ± 15 mm (standard)
900 mm ± 15 mm (SMEMA)
930 mm ± 15 mm (SMEMA)
950 mm ± 15 mm (SMEMA)
Weight
without feeder
with feeders at every location
with compressed air supply for bulk case feeder
and adapter for the 3rd tape reel
Approx. 105 kg
Approx. 145 kg
Approx. 170 kg
User Manual SIPLACE HF Series 6 Component handling
Software Version SR.505.xx 05/2004 US Edition 6.3 Component trolley
261
6
6.3.3 Dimensions and center of gravity
6
Fig. 6.3 - 4 Dimensions (all in millimeters)
The center of gravity (A) of the component trolley was determined under the following conditions:
– Component trolley set to a PCB transport height of 950 mm.
– Feeders in all 15 locations.
Reel diameter
Standard
Maximum
Up to 432 mm (17")
483 mm (19")
Feeder locations Max. 15
Changeover time for the component trolley Less than 1 min.