FX-3RA_SPE_EN.pdf - 第12页

- 8 - 4- 2. Mechanical/Electrical Speci fica tion s 4-2-1 Us age environment conditions FX - 3R A Power supply V oltage Three - phas e 200V , 220V , 240V , 380V , 400V , 415V AC ±10% (see Note 1) Frequency 50/60 Hz Rated…

- 7 -

4. SPECIFICATIONS

4-1. Basic specifications

① Basic specifications

FX-3RA

Board specifications

L-PWB

XL-PWB

Board

dimensi

ons

Standard

410×360mm

610×560mm

L-Wide

（

Option

）

510×360mm -

Longer sized

PWB in X

axis (Option)

800×360mm(L､L-wide)

800×560mm

Board transport

reference position

Front side or rear side Front side

Supported languages

English, Japanese, Chinese and Korean

Conveyor height

900/950±20mm (for Japan, China, Korea and South east Asian

countries) (Note1)

950±20mm (for Europe and the U.S.A.)

Component height

6mm specifications (SC)

Component size

0402 to 33.5mm

Component placement

speed

（

IPC9850

）

66,000(CPH) (Note2) 51,500(CPH) (Note2)

Placement accuracy

±50μm (Cpk

≧

Number of component to

be placed

A maximum of 240 types(on a Electric Double Tape feeder)

EN Specifications

Enable

Note1 The board transport height of 950 ± 20 mm (for Japan, China, Republic of Korea, and

South East Asia) is an option.

Note 2 For the component placement speed when the placement monitor is used, refer to 4-3

Placement cycle time.

②Recognition devices and heads.

Recognition device

Description

Standard LNC60

The laser sensor LNC60 allows six nozzles to

pick up components at the same time and

recognize them on the fly at a time.

Option LNC61

This is a laser sensor equipped with a

subminiature camera for a Placement Monitor.

- 8 -

4-2. Mechanical/Electrical Specifications

4-2-1 Usage environment conditions

FX-3RA

Power supply

Voltage

Three-phase 200V, 220V, 240V, 380V, 400V, 415V AC ±10%

(see Note 1)

Frequency 50/60 Hz

Rated apparent

power

Maximum 8.5 kVA

Air supply

Air pressure 0.50 ± 0.05 MPa dry air

Maximum air

consumption

150 L/min (ANR) (see Note 2)

Environment

requirements

During

operation

Temperature

10°C to 35°C

Accuracy guaranteed

temperature

20°C to 25°C

Humidity 30 to 80% RH (No condensation)

Altitude 1,000m or less

Transportation

or storage

Temperature

-15°C to 70°C

Humidity 20% to 95%RH (No condensation)

Noise 75 dB (A) or less (see Note 3)

Installation conditions

(For EN machine)

Overvoltage category Category Ⅲ according to IEC60664-1

Pollution degree Degree 3 according to IEC60664-1

Note 1: Any power supply cable for the primary side is not supplied with the machine.

We make no warranties against any accident of the primary side wiring caused by

short-circuit of a power cable and so on. Be sure to select the appropriate breaker

and power cable at your own risk.

Use a 8-mm

or more diameter of a power cable for each phase at the primary side.

Note that the appropriate cross-section area of a power cable varies depending on

its class, facility condition, length and the supplied power voltage. Therefore, be

sure to use a power cable that conforms to the regulations of the installation site.

Applicable sectional areas of primary side power cable lengths

Supply power

Primary-side power cable length(m)

Less than 20m 30m 40m 50m

AC 200/220/240V

Applicable

sectional area

(mm

)

8 8 10 12

AC 380/400/415V 8 8 8 8

Note that a 3-phase 50 A breaker is attached on the power supply incoming section

of FX-3RA.

Peak current (when 200 V AC 3-phase power supply is used): 90 A

Note 2: About ANR: Temperature 20

C,Absolute pressure 0.1 MPa (= 100 kPa=1 bar) and

Relative humidity 65%

The necessary air supply shall be calculated as follows:

In case of 150 L/min (ANR), 150/0.926 = 162 L/min: 162 L/min or more air supply

is required.

Note 3: This value was measured with conforming to the JIS Z8731 regulation.

- 9 -

4-2-2 Outside dimension (except for the largest projections)

L-PWB, L-Wide-PWB specification (Unit: mm)

2020/2070

1650 (L,L-Wid e )

2420(L,L-Wid e )

2650(L) , 28 80 ( L-Wi de )

基板搬送高さ

900/950

1530/1580

1995/2045

XL-PWB specification

2020/2070

1850

2430

2880

基板搬送高さ

900/950

1530/1580

1995/2045

4-2-3 Mass

L-PWB、L-Wide-PWB specification: 3,500kg

XL-PWB specification: 3,750kg

4-3. Component placement Cycle Time (A number of components to

be placed per an hour)

L-PWB、L-Wide-PWB specification: 66,000 CPH (IPC9850)

XL-PWB specification: 51,500 CPH (IPC9850)

*1: This is a number of components to be placed for one hour when 400 1608, 1005 or

0603 components are placed onto 200 mm × 200 mm board at an angle of 0, 90, 180

and 270 degrees sequentially.

*2: The mounter places a 0402 component sequentially, and the cycle time is 51,500CPH

(for L, L-wide PWB) and 40,500CPH (for XL PWB).

*3: When you use the 0402 component support function to place a 0402 component on a

board, the mounter does not pick up two or more 0402 components simultaneously.

However, it can pick up a 0402 component(s) and other type component(s)

simultaneously if the other head is located within the simultaneous pick-up area viewed

from the placement head for a 0402 component.

*4: When the placement monitor is used, the placement cycle time of 3% max. becomes

slower. When the “The system pauses if a component existence error occurs” is used

in the placement monitor setting, the placement cycle time of 40% max. becomes

slower.

Conveyor height

(90)