3OM-1054-002.pdf - 第4页
About the Instruction Manual V olume 5: Pneumatic and Electrical Diagrams This provides various kinds of material such as pneu- matic and electrical circuit diagrams for those who are in charge of machine servicing opera…
About the Instruction Manual
• This instruction manual is classified into several volumes on subjec-
tive basis as follows.
Volume 1: Operation (Operator)
This describes the fundamentals for those who read
this instruction manual and use the component place-
ment machine for the first time.
Coverage: This covers the checking items, the safety
precautions, the scope of the machine, the
preparatory and ending procedures of au-
tomatic operation, and the troubleshooting
on simple errors.
Volume 2: Operation (Supervisor)
This describes the general items related to machine
operations for those who have learned how to operate
the machine.
Coverage: This covers the specifications and func-
tions of the machine, various menus re-
lated to the program change, automatic op-
erations, and maintenance, etc.
Volume 3: Programming and Machine Data
This describes various data for a programmer(s) who
creates pattern programs and a supervisor who must
understand the meanings of various data.
Coverage: This covers the various data such as pat-
tern program, component library data and
the menus for production control and sys-
tem settings.
Volume 4: Maintenance and Troubleshooting
This describes periodic maintenance operations,
troubleshooting, etc., for those who use this machine.
Coverage: This covers periodic maintenance opera-
tions, the list of consumables and servic-
ing parts, troubleshooting on simple errors,
and error messages and remedial mea-
sures against simple errors.
INSTRUCTION MANUAL
CHIP MOUNTER
TCM-X100J
Volume 1 : Operation (Operator)
INSTRUCTION MANUAL
CHIP MOUNTER
TCM-X100J
Volume 2 : Operation (Supervisor)
01 12-003 2 AGS01EDTP
Fig. 3X2
Fig. 3X3
INSTRUCTION MANUAL
CHIP MOUNTER
TCM-X100J
Volume 3 : Programming and
Machine Data
Fig. 3X4
INSTRUCTION MANUAL
CHIP MOUNTER
TCM-X100J
Volume 4 : Maintenance and
ޓTroubleshooting
Fig. 3X5
About the Instruction Manual
Volume 5: Pneumatic and Electrical Diagrams
This provides various kinds of material such as pneu-
matic and electrical circuit diagrams for those who are
in charge of machine servicing operations.
Coverage: Pneumatic Diagram, Parts Location, Elec-
trical Circuit Diagrams, etc.
COMPONENT LIBRARY:
This describes an explanation of component library data
and how to create it.
• This manual may not be copied, in whole or part, with-
out written consent of the publisher.
• This manual should be regarded as part of the ma-
chine and the contents comply with all the specifica-
tions regarding the purchased machine. Please keep
this manual within reach to serve as a handy tool in
completely understanding the workings of this ma-
chine.
• The contents of this manual are subject to change
without prior notice.
01 12-003 3
AGS01EDTP
INSTRUCTION MANUAL
CHIP MOUNTER
TCM-X100J
Volume 5 : Pneumatic and
Electrical Diagrams
INSTRUCTION MANUAL
TCM-X Series
CHIP MOUNTER
COMPONENT LIBRARY
Fig. 3X6
Fig. 3X7
Contents
Page
Before Use .......................................................................................... 1
About the Instruction Manual ............................................................ 2
Contents .............................................................................................. 4
Checking Items.................................................................................... 9
Safety Precautions .............................................................................. 11
Section 1 Scope
........................................................................1- A
1. Outline of Data .............................................................................1- 1
Section 2 Pattern Program
.................................................2- A
1. Outline of Pattern Program ........................................................2- 1
1.1 Composition of Pattern Program ...........................................2- 1
1.1.1 Outline of Various Data ......................................................2- 2
1.1.2 Input Procedure of Each Data ...........................................2- 2
1.2 Composition of Operation Data .............................................2- 3
1.3 Composition of Placement Feeder Location Data ...............2- 5
1.4 Composition of Placement Data.............................................2- 6
2. Pattern Program ..........................................................................2- 7
2.1 Types of P.C.B.’s and Required Data .....................................2- 7
2.2 Pattern Program Name............................................................2-13
2.3 Operation Data.........................................................................2-13
2.4 Placement Feeder Location Data ..........................................2-40
2.5 Placement Data ........................................................................2-43
3. Example of Pattern Program Creation ......................................2-57
3.1 Single Pattern ..........................................................................2-57
3.2 Single Pattern (P.E.C. Recognition Function Enabled) .......2-60
3.3 Repetitive Patterns .................................................................2-63
3.4 Repetitive Patterns (Unit P.C.B. B.B.R. Enabled) ................2-65
3.5 Repetitive Patterns
(Unit P.C.B. B.B.R. Function Enabled)...............................2-68
3.6 Repetitive Patterns (Block Sorting Enabled) .......................2-71
3.7 Repetitive Patterns
(Polar Coordinate Conversion Function) .........................2-74
3.8 Multi-Model Repetitive Patterns ...........................................2-75
0307-005 4 AGS01EDTP