00196602-05_SM_SIPLACE_X-Feeder_EN.pdf - 第22页
6 Repairing the X Feeder modules 6.2 Rear Sliding Guide 22 Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 6.2.1 Removing the Rear Sliding Guide NOTICE The pickup window must be fitted To prevent damage to the sprocket…
6 Repairing the X Feeder modules
6.2 Rear Sliding Guide
Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 21
6.1.2 Fitting the Front Sliding Guide
NOTICE
The pickup window must be fitted
To prevent damage to the sprocket wheel and the reject device, make sure that the pickup
window is fitted for this work.
► Insert the sliding guide - as shown in the diagram
- into the groove on the drive carrier.
► Position the front sliding guide so that you can
see the holes for the screws through the sliding
guide.
► Fix the sliding guide to the feeder module with
the 2 Phillips head screws (M3x10mm).
► Press the sliding foil slightly together.
► Push the sliding foil from the front into the sliding
guide, until it engages audibly.
6.2 Rear Sliding Guide
Required spare parts
Fig.2: Rear sliding guide L200
Feeder module Item no. Designation
4–88mm 03003994-Sxx Sliding guide/rear L200
Required tools
●
Phillips screwdriver
●
TORX screwdriver size T8
6 Repairing the X Feeder modules
6.2 Rear Sliding Guide
22 Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017
6.2.1 Removing the Rear Sliding Guide
NOTICE
The pickup window must be fitted
To prevent damage to the sprocket wheel and the reject device, make sure that the pickup
window is fitted for this work.
► Loosen the 3 rear screws on the sliding guide. (1)
► Loosen the front screw on the sliding guide. (2)
► Lift the sliding guide up at the back and pull up-
wards and off.
6.2.2 Fitting the Rear Sliding Guide
NOTICE
The pickup window must be fitted
To prevent damage to the sprocket wheel and the reject device, make sure that the pickup
window is fitted for this work.
► Fit the sliding guide – as shown in the diagram –
to the underside of the feeder module.
(1) Push the left part of the rear sliding guide (as
shown in the diagram) as far left as the stop, to-
wards the front sliding guide and into the recess.
(2) Then lower the two snap tabs of the sliding
guide into the openings provided on the under-
side of the feeder module.
► (3) Screw the sliding guide to the feeder module
at the front with the cylinder head screw
(2.5x8mm) and spring circlip.
Note:
When using feeder modules with a width of 4-
12mm, use the mushroom head cutting screws
(T82.5x10mm).
For feeder modules of 16mm width and above,
use cylinder head screws (2.5 x 8mm).
► (4) Screw the sliding guide onto the back of the
feeder module.
6 Repairing the X Feeder modules
6.3 Left Side Cover
Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 23
6.3 Left Side Cover
CAUTION
Observe the ESD regulations!
Pay attention to feeder module ESD safety:
Before you open the side cover, make sure you are wearing the ESD protection wristband,
to prevent damage to the highly sensitive boards inside the feeder module.
Required spare parts
Example: side cover on left 4-12mm
Feeder module Item no. Designation
4+ 8mm 03052072-Sxx Cover assembly on left feeder side, /X8
12 mm 03021934-Sxx Cover /left feeder side X12
16–88mm 03021215-Sxx Cover /left feeder side X16 - 88
Required tools
●
Phillips screwdriver 0.9Nm
●
TORX screwdriver 0.6Nm, size T8
●
Small Phillips screwdriver
6.3.1 Removing the Left Side Cover
► Only for 4–12mm feeder modules:
Remove the back sliding guide (see 6.2.1 "Re-
moving the Rear Sliding Guide" [}22]).
► Carefully place the feeder module with the right-
side side down on a stable, level and clean sur-
face.
► Loosen the screws as shown in the diagram.
Green arrows point to the screws for which you need a
TORX screwdriver with a torque of 0.6Nm.
Blue arrows point to the screws for which you need a
Phillips screwdriver with a torque of 0.9Nm.
Start to loosen the screws at the position shown by the
green arrow.
For greater clarity, we recommend that you loosen the
same types of screws together and then keep them in
small, marked bowls.