00196602-05_SM_SIPLACE_X-Feeder_EN.pdf - 第41页
6 Repairing the X Feeder modules 6.5 Foil Disposal Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 41 ► (1) Pull the connector marked in the diagram up and out of its connection. To loosen the connector, move it carefu…
6 Repairing the X Feeder modules
6.5 Foil Disposal
40 Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017
► Fix the foil disposal drive into place with the 5
screws marked in the diagram.
Use a TORX screwdriver with a torque of 0.6 Nm for
the (1) countersunk screws M2.5x5mm
.
Use a Phillips screwdriver with a torque of 0.9 Nm for
the (2) mushroom head cutting screw T2.5x6mm.
6.5.1.3 Removing the Foil Disposal Drive (16 mm)
► First remove the rocker (see 6.6.2.1 "Removing
the Rocker (4 - 88 mm)" [}69]).
► Carefully place the feeder module down on its left
side.
► Remove the screws marked in the diagram.
► Carefully place the feeder module on its right
side.
► Remove the left side cover (see 6.3.1 "Removing
the Left Side Cover" [}23]).
► Loosen the screws marked in the diagram.
► Remove the spacer from the feeder module.
6 Repairing the X Feeder modules
6.5 Foil Disposal
Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 41
► (1) Pull the connector marked in the diagram up
and out of its connection.
To loosen the connector, move it carefully from
side to side.
► (2) Pull the connector marked in the diagram out
of its connection in the direction of the arrow. Pull
on the connector and NOT on the cable.
► (3) Carefully swing the lock on the flat ribbon
cable connection up to the left and release the
flat ribbon cable.
Make sure that the lock is not pushed too far
back. It could break off if you do this.
► Pull the connector shown in the diagram out of its
connection in the direction of the arrow. Pull on
the connector and NOT on the cable.
► Remove the foil drive, together with the foil con-
tainer, out of the feeder module.
► Turn the foil disposal drive over.
► (1) Loosen the screws marked in the diagram.
► Turn the foil disposal drive over again.
► (2) Loosen the screws marked in the diagram.
NOTICE!
Make sure that the washers belonging to the
screws are not lost.
.
► Remove the foil disposal drive.
While doing so, bend the frame on the left side
slightly towards the back and tilt the foil disposal
drive out towards the front.
6 Repairing the X Feeder modules
6.5 Foil Disposal
42 Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017
6.5.1.4 Fitting the Foil Disposal Drive (16 mm)
► While doing so, bend the frame on the left side
slightly towards the back and press the foil dis-
posal drive into the frame.
► (1) Press the foil disposal drive in the direction of
the arrow and into the foil container.
Make sure that the foil disposal drive is directly
aligned flush against the foil container.
► Insert the washer and fix the foil disposal drive
with the cylinder head screws marked in the dia-
gram.
► Turn the foil disposal drive over.
► (2) Fix the foil disposal drive into place with the
screws marked in the diagram.
(A) cylinder head screw with washer
(B) mushroom head cutting screw (Torx)
► Turn the foil disposal drive over again.
► Place the rubber seal into the fixture as marked
in the diagram.
On the left-hand side, this rubber seal should be
flush while on the right-hand side it should project
somewhat. The spacer will then be fitted to this
projected part of the rubber seal.