00196602-05_SM_SIPLACE_X-Feeder_EN.pdf - 第5页

1 Introduction 1.1 Safety Instructions Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 5 1 Introduction This manual describes service work performed on the SIPLACE® 4-88 mm X feeder modules. 1.1 Safety Instructions DAN…

100%1 / 90
4 Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017
Contents
6.4.3 Magnetic Shield (4mmX Only).. 35
6.4.3.1 Removing the Magnetic Shield.. 35
6.4.3.2 Fitting the Magnetic Shield.. 36
6.5 Foil Disposal.. 37
6.5.1 Foil Disposal Drive Assembly.. 37
6.5.1.1 Removing the Foil Disposal Drive (4 - 12 mm).. 38
6.5.1.2 Fitting the Foil Disposal Drive (4 - 12 mm).. 39
6.5.1.3 Removing the Foil Disposal Drive (16 mm).. 40
6.5.1.4 Fitting the Foil Disposal Drive (16 mm).. 42
6.5.1.5 Removing the Foil Disposal Drive (24 - 88 mm).. 44
6.5.1.6 Fitting the Foil Disposal Drive (24 - 88 mm).. 46
6.5.2 Stripping Device Foil Disposal.. 49
6.5.2.1 Removing the Stripping Device (4 mm).. 49
6.5.2.2 Fitting the Stripping Device (4 mm).. 50
6.5.2.3 Removing the Stripping Device (8-88mm).. 50
6.5.2.4 Fitting the Stripping Device (8–88mm).. 50
6.5.3 Knurled Tamp Wheel.. 51
6.5.3.1 Removing the Knurled Tamp Wheel (4 - 88 mm).. 52
6.5.3.2 Fitting the Knurled Tamp Wheel (4 - 88 mm).. 52
6.5.4 Foil Rocker.. 53
6.5.4.1 Removing the Foil Rocker (4 - 88 mm).. 54
6.5.4.2 Fitting the Foil Rocker 4 - 88 mm).. 55
6.5.5 Ratchet.. 56
6.5.5.1 Removing the Ratchet (4 - 12 mm).. 56
6.5.5.2 Fitting the Ratchet (4 - 12 mm).. 58
6.5.5.3 Removing the Ratchet (16 - 88 mm).. 59
6.5.5.4 Fitting the Ratchet (16 - 88 mm).. 61
6.5.6 Tape Disposal Flap.. 65
6.5.6.1 Removing the Flap (4–12mm).. 65
6.5.6.2 Fitting the Flap (4–12mm).. 66
6.5.6.3 Removing the Flap (16–88mm).. 66
6.5.6.4 Fitting the Flap (16–88mm).. 66
6.6 Rocker.. 67
6.6.1 Rocker Stripping Device (4mm only).. 67
6.6.1.1 Removing the Rocker Stripping Device.. 67
6.6.1.2 Fitting the Rocker Stripping Device.. 68
6.6.2 Rocker Assembly.. 68
6.6.2.1 Removing the Rocker (4 - 88 mm).. 69
6.6.2.2 Fitting the Rocker (4 - 88 mm).. 70
6.6.3 Tamp Wheel for Rocker.. 71
6.6.3.1 Removing the Tamp Wheel for the Rocker (4 - 88 mm).. 72
6.6.3.2 Fitting the Tamp Wheel for the Rocker (4 - 16 mm).. 72
6.6.3.3 Fitting the Tamp Wheel for the Rocker (24 - 88 mm).. 72
6.6.4 Bearing Shaft.. 73
6.7 Operating Panel Assembly.. 74
6.7.1 Removing the Operating Panel (4+8 mm).. 74
6.7.2 Fitting the Operating Panel (4+8mm).. 75
6.7.3 Removing the Operating Panel (12 mm).. 76
6.7.4 Fitting the Operating Panel (12 mm).. 78
6.7.5 Removing the Operating Panel (16 - 88 mm).. 81
6.7.6 Fitting the Operating Panel (16 - 88 mm).. 83
6.8 Leaf Spring.. 87
6.8.1 Removing/Fitting the Leaf Spring (4 - 12 mm).. 87
6.8.2 Removing/Fitting the Leaf Spring (16 - 88 mm).. 88
1 Introduction
1.1 Safety Instructions
Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 5
1 Introduction
This manual describes service work performed on the SIPLACE® 4-88 mm X feeder modules.
1.1 Safety Instructions
DANGER
Nonobservance of these safety instructions may cause injury to personnel and dam-
age to the machine!
► Please observe the safety instructions in the user manual of the relevant machine
for all work!
1.1.1 Conventions for the Use of Safety Instructions and Symbols
Safety Instructions
This manual contains notes that must be observed to guarantee your personal safety and to avoid
damage to equipment. These notes are highlighted by warning triangles and are indicated as fol-
lows according to the level of risk:
DANGER
Definition
For the purposes of this manual, this indicates that fatal or severe injuries or considerable
damage to property will occur if this hazard warning is not observed.
WARNING
Definition
For the purposes of this manual, this indicates that fatal or severe injuries or considerable
damage to equipment may occur if these warning instructions are not followed.
CAUTION
Definition
For the purposes of this manual, this indicates that minor injuries or damage to property
may occur if this caution is not observed.
NOTICE
Definition
For the purposes of this manual, this note provides information about the product or indic-
ates a part of the manual that requires particular attention.
Symbols
Example Description
Next This typeface marks controls and interface elements in the software.
► These symbols indicate actions that have to be performed by the operator.
1 Introduction
1.2 Environmentally-Friendly Disposal of Materials and Components
6 Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017
1.2 Environmentally-Friendly Disposal of Materials and
Components
SIPLACE products are manufactured using only materials and parts that can be easily separated
and disposed of in an environmentally-friendly way.
NOTICE
Observe the applicable regulations
The company operating the system has sole responsibility for the proper, environmentally-
friendly disposal of machines, working materials, consumables and wear parts.
► Please observe your national statutory provisions for waste disposal and environ-
mental protection.
1.3 Use of Original SIPLACE Accessories and Spare Parts
Only use original spare parts and authorized accessories. The use of other parts will affect safety
and will invalidate the liability for any consequential damage.
1.4 Information About This Service Manual
WARNING
Additional qualifications required
The service work described in this manual may only be performed by specially trained per-
sonnel and therefore requires additional qualifications and skills.
Please contact your SIPLACE service team if you have any special questions about service work.
1.5 Release History
Release Changes
03/2009 First edition
05/2012 Supplement SmartFeeder 2x8 mm X
Supplement SmartFeeder 12 mm X and 16 mm X
02/2013 Supplement 4 mm X feeder
10/2014 Supplement SmartFeeder 4 mm X and 8 mm X
1.6 SIPLACE on the World Wide Web (WWW)
Log into our SIPLACE® homepage at http://www.siplace.com.
You can choose between the German and English versions.
The different sections contain information about our products, services and contact persons.
In addition, registered customers can also access the MySIPLACE user group. Here you can call
up special information about our placement systems, e.g.
●
technical documentation
●
technical information
●
spare parts lists etc.
Registration for theMySIPLACE user group is very simple:
► Click at the head of the web site on
and then on the Register
link.
► Fill in the registration form and send it off to us.
Soon afterwards, you will receive your access authorization with user name and password