00196602-05_SM_SIPLACE_X-Feeder_EN.pdf - 第30页
6 Repairing the X Feeder modules 6.4 Tape Drive 30 Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 6.4.1.3 Removing the Pickup Window (16 - 88 mm) ► (1) Loosen the two marked screws which fasten the spring holder to th…
6 Repairing the X Feeder modules
6.4 Tape Drive
Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 29
► Fix the pickup window with a bearing screw.
► Insert the compression spring into the recess in
the tape drive.
► Place the spring holder onto the compression
spring, so that it engages into the spring holder
and the two holes for the screws can be seen
through the spring holder.
► Fix the spring holder with the two countersunk
screws (M 2 x 4mm).
For 12mmX feeders only
► Insert the filler piece into the feeder module.
Make sure that the filler piece is aligned flush
against the feeder module.
► Fix the filler piece with the screws marked in the
diagram.
6 Repairing the X Feeder modules
6.4 Tape Drive
30 Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017
6.4.1.3 Removing the Pickup Window (16 - 88 mm)
► (1) Loosen the two marked screws which fasten
the spring holder to the pickup window.
► Remove the two screws, the tape spring and the
spring holder out of the pickup window.
► (2) Loosen the marked screw on the left-hand
side of the feeder module.
► (3) Loosen the marked screw on the right-hand
side of the feeder module.
► First lift the pickup window at the back.
► Tilt the pickup window, incline it to the left and lift
it off the feeder module.
6.4.1.4 Fitting the Pickup Window (16 - 88 mm)
► (1) Lift the reject device and hold with one finger.
► (2) Hold the pickup window inclined and hook
from the left into the opening in the feeder mod-
ule.
► (3) Swivel the pickup window so that the back
part is over the feeder module and hold the
pickup window in a horizontal position.
Make sure that the pickup window also projects
beyond the feeder module on the right outer side.
► Lower the pickup window over the snap tabs on
the feeder module.
The pickup window should be fitted loosely on
the feeder module.
6 Repairing the X Feeder modules
6.4 Tape Drive
Service Manual SIPLACE X-Feeder 4 - 88 mm 11/2017 31
► (1) Fasten the pickup window to the left side of
the feeder module.
Use the bearing screw X16-88, item no.
03021264-xx for this.
► (2) Fix the pickup window to the right-hand side
of the feeder module.
When using feeder modules with widths of 16,
32–56 and 88mm, use the bearing screw
X16-88, item no. 03021264-xx
For feeder modules with widths of 24mm and
72mm, use the shorter bearing screw X24x72,
item no. 03012350-xx.. You will need to place a
washer underneath when fitting this screw (bush-
ing), item no. 03007433-xx.
► Insert the tape spring into the hole.
► Hold the spring holder so that the straight side is
on the outside.
► Position the spring holder with the recess on the
tape spring.
► Initially fix the spring holder loosely with a screw.
Do not tighten the screw yet, to avoid distorting
the spring holder and screws.
► Fix the spring holder with the second screw.
► Now tighten the first screw.
6.4.2 Splice Sensor
Required spare parts
Example:splice sensor 8-12mm (left), 16-88mm(right)
Feeder module Item no. Designation
8–12mm 03060695-Sxx Splice sensor B3+ / X8-X12
16–88mm 03038133-Sxx Splice sensor S5
Required tools
●
TORX screwdriver size T8
●
Phillips screwdriver