Printer 600 Machine Programming.pdf - 第101页
0$&+,1 (352*5$0 0,1* 0(18 3$5 $0( 7(5 6 Software Version 07SP04 User Manual 1.101 NOTE This par ameter is only disp layed if Knead Off-image is set to enabled. Knead Af ter Replenish If this opt ion is enabled and …
0$&+,1(352*5$00,1*
0(183$5$0(7(56
1.100 User Manual Software Version 07SP04
printing and between print strokes.
NOTE
Only available while ProFlow and the Software Controlled Air Regulator (SCAR)
are fitted.
Knead Paste
Pressure
This parameter sets the pressure to be applied, while using ProFlow, when
kneading.
NOTE
The default value for this parameter is Print Paste Pressure, ie when the Print
Paste Pressure is altered, Knead Paste Pressure follows it.
Knead Deposits This parameter sets the number of print strokes to be carried out on each of the
kneaded boards.
Knead Boards This parameter sets the number of boards to be printed using the knead
sequence.
Knead Off-image This parameter sets whether ProFlow is to knead in an off-image area of the
stencil. Options are:
NOTE
With Knead Off Image enabled, Stencil Protection must be switched Off.
Paste Knead
Period
This parameter sets the time period between print cycles which, if exceeded,
initiates a paste knead sequence.
Knead Before Print This parameter sets ProFlow to knead before printing the first board and the
amount of boards to be printed between kneading.
Minimum Maximum Increment Default
0.0 bar 4.0 bar 0.2 bar 0.0 bar
Minimum Maximum Increment Default
0.0 bar 4.0 bar 0.2 bar see Note
Minimum Maximum Increment
2201
Minimum Maximum Increment
1101
Options Available Default
Enabled Enabled
Disabled
Minimum Maximum Increment
0 (paste kneading switched off) 30 minutes 1 minute
0$&+,1(352*5$00,1*
0(183$5$0(7(56
Software Version 07SP04 User Manual 1.101
NOTE
This parameter is only displayed if Knead Off-image is set to enabled.
Knead After
Replenish
If this option is enabled and a replenishment of transfer material has been
performed, a knead paste is performed (as defined by the knead paste param-
eters in the board file) on the next board.
Knead After
Dispense
If this option is enabled and a paste dispense has been performed, a knead
paste is performed (as defined by the knead paste parameters in the board file)
on the next board.
Clean After Knead This parameter sets the cleaning mode that is applied following a knead paste.
The options are:
NOTE
While a Vortex cleaner is fitted, either mode may be selected, but the Vortex
cleaner only makes a single stroke.
Print Gap This parameter sets the gap required between the stencil and board to be
printed during the print stroke.
Under Clearance This parameter determines the clearance provided between the underside of
the board and the top of the machine tooling to allow for components on the
underside of the board.
Minimum Maximum Increment Default
0
(disables knead before printing)
100 1 0
Options Available
Enabled
Disabled
Options Available
Enabled
Disabled
Options Available
Disabled
Mode 1
Mode 2
Minimum Maximum Increment
0.0mm 6.0mm 0.025mm
Minimum Maximum Increment Default
3.0mm 42.0mm 0.1mm 19.0mm
0$&+,1(352*5$00,1*
0(183$5$0(7(56
1.102 User Manual Software Version 07SP04
Separation Speed This parameter sets the speed at which the rising table drives down the
separation distance.
Separation
Distance
This parameter sets the separation distance between board and stencil. The
parameter can help increase cycle time when a low separation speed is used
by decreasing the separation distance.
Board Count This function provides the facility for the print cycle to be halted automatically
on a board count basis.
If the board stop count is zero this function is not active. When a print run is
started, a count is made from the STOP CYCLE AFTER value to zero decre-
menting by one for each board printed.
When the counter reaches zero, the print cycle is finished and control returned
to the main display page and the beacon is set to amber, thus indicating that the
machine requires operator attention.
The operator has access to all of the machines options. Once the operator has
performed any required operations, the run button can be pressed to continue
the print cycle.
Separation Delay This parameter is the time in seconds that the table delays before lowering. This
delay occurs during screen cleaning and after the flood. This parameter only
becomes available when Adhesive has been selected in the Print Mode
parameter.
Print Mode This parameter sets the mode of operation of the machine. Available modes
are:
Paste Ridge
Removal
This parameter enables the cleaning option Paste Ridge Removal. This option
removes the ridge of paste that can develop on the underside of the stencil at
Minimum Maximum Increment
0.1mm/sec 20.0mm/sec 0.1mm/sec
Minimum Maximum Increment Default
0.0mm 3.0mm 0.1mm 3.0mm
Minimum Maximum Increment
0 Boards 500 Boards 1 Board
Modes Available Note Default
Print / Print Print / Print
Print / Flood
Flood / Print
Adhesive Selecting Adhesive from this parameter
opens the separation delay and print vacuum
mode