Printer 600 Machine Programming.pdf - 第29页
0$&+,1 (352*5$0 0,1* 67$*( %9$&8 80722/,1* Software Version 07SP04 User Manual 1.29 machine. The following window and menu bar is di splayed: NOTE If cont aminate d squeegees are fi tted, t hese should b e…
0$&+,1(352*5$00,1*
67$*(%9$&880722/,1*
1.28 User Manual Software Version 07SP04
displayed.
16.Select Open Cover (F2).
17.Either:
a. Open the front printhead cover.
or
b. Raise the printhead shutter.
18.The vacuum box can now be fitted into the appropriate location holes in the
tooling plate. Ensure the vacuum box is placed into the correct set of holes
taking regard of the type of stencil being used. Connect the vacuum hose
to the vacuum box inlet, ensure the hose is routed clear of any parts.
19.Either:
a. Close the front printhead cover.
or
b. Lower the printhead shutter.
20.Press the System button.
21.Select Board Width (F5). The message ‘Checking for a board on the
belts’ is displayed. Whilst the rear rail is moving the message ‘Rail
Moving...’ is displayed.
22.Select Generic Tooling (F7). The print carriage moves to the front of the
Adjust
Open
Cover
Home
Cleaner
Board
Stop
Full
Width
Load
Width
Generic
Tool ing
Exit
Adjust
Open
Cover
Home
Cleaner
Board
Stop
Board
Width
Load
Width
Generic
Tool ing
Exit
Adjust
Open
Cover
Home
Cleaner
Board
Stop
Board
Width
Load
Width
Generic
Tool ing
Exit
0$&+,1(352*5$00,1*
67$*(%9$&880722/,1*
Software Version 07SP04 User Manual 1.29
machine.
The following window and menu bar is displayed:
NOTE
If contaminated squeegees are fitted, these should be replaced at this point.
23.Select Continue (F1). Cleaner moves to the Home position and the print
carriage moves to the rear of the machine. The message ‘Table at Home
Height’ is displayed.
24.Select Transprt Height (F3). The message ‘Table at Transport Height’ is
displayed.
25.Place a board on the input sensor of the upline conveyor of the machine.
26.Select Load (F1).
27.Select Auto Board (F1).
28.Select Vision Height (F3). The message ‘Table at Vision Height. Check
Tooling Clearance’ is displayed.
Adjust
Open
Cover
Home
Cleaner
Board
Stop
Full
Width
Load
Width
Generic
Tooling
Exit
Generic Tooling Warning
WARNING Paste may drip into the machine
Remove Squeegees NOW
Continue
Open
Cover
Exit
Continue
Open
Cover
Exit
Load
Transprt
Height
Board
Clamps
Change
Screen
Open
Cover
Exit
Load
Vision
Height
Home
Height
Board
Clamps
Change
Screen
Open
Cover
Exit
Auto
Board
Manual
Board
Exit
Unload
Vision
Height
Home
Height
Board
Clamps
Change
Screen
Open
Cover
Exit
0$&+,1(352*5$00,1*
67$*(%9$&880722/,1*
1.30 User Manual Software Version 07SP04
29.Select Contact Height (F3).
The following window and menu bar is displayed:
30.Select Continue (F1). The message ‘Table at Contact Height. Check
Tooling Clearance’ is displayed.
31.Select Open Cover (F7).
32.Either:
a. Open the front printhead cover.
or
b. Raise the printhead shutter.
33.Check that the setup of the tooling is adequate for the board, adjust as
necessary.
NOTE
If adjustment is required, this can be carried out at Transport Height.
34.Either:
a. Close the front printhead cover.
or
b. Lower the printhead shutter.
35.Press the System button.
36.Select Exit (F8).
Contact
Height
Tra nspr t
Height
Change
Screen
Open
Cover
Exit
Contact Height Warning
WARNING Check for obstructions between
the Rails and the Screen
Continue
Open
Cover
Exit
Continue
Open
Cover
Exit
Vision
Height
Open
Cover
Exit
Exit