Printer 600 Machine Programming.pdf - 第113页

0$&+,1 (352*5$0 0,1* 0(18 3$5 $0( 7(5 6 Software Version 07SP04 User Manual 1.113 A positive of fset moves the print to the righ t of the board. Reverse Y Offset Programmable offse t of the print on the board when …

100%1 / 128
0$&+,1(352*5$00,1*
0(183$5$0(7(56
1.112 User Manual Software Version 07SP04
NOTE
See Fiducial 1X Coordinate above for information on warning window.
Fiducial 3 Y
Coordinate
Distance of the third fiducial from the front edge of the board.
NOTE
See Fiducial 1X Coordinate above for information on warning window.
Select Mark X Distance of the select mark from the right or left hand edge of the board
(configuration dependent).
NOTE
Only used while Selective Print/Pass is enabled in Set Preferences.
Select Mark Y Distance of the select mark from the front edge of the board.
NOTE
Only used while Selective Print/Pass is enabled in Set Preferences.
Forward X Offset Programmable offset of the print on the board when printing from the rear.
A positive offset moves the print to the right of the board.
Forward Y Offset Programmable offset of the print on the board when printing from the rear.
A positive offset moves the print to the rear of the board.
Forward Theta
Offset
Programmable offset of the print on the board when printing from the rear.
A positive offset moves the print in a clockwise direction.
Reverse X Offset Programmable offset of the print on the board when printing from the front.
Minimum Maximum Increment Default
1.0mm Board Width 0.1mm 1.0mm
Minimum Maximum Increment Default
0.0mm Board Length 0.1mm 148.5mm
Minimum Maximum Increment Default
0.0mm Board Width 0.1mm 13.0mm
Minimum Maximum Increment
-1.0mm +1.0mm 0.004mm
Minimum Maximum Increment
-1.0mm +1.0mm 0.004mm
Minimum Maximum Increment
-1000 arc seconds +1000 arc seconds 2 arc seconds
0$&+,1(352*5$00,1*
0(183$5$0(7(56
Software Version 07SP04 User Manual 1.113
A positive offset moves the print to the right of the board.
Reverse Y Offset Programmable offset of the print on the board when printing from the front.
A positive offset moves the print to the rear of the board.
Reverse Theta
Offset
Programmable offset of the print on the board when printing from the front.
A positive offset moves the print in a clockwise direction.
Screen X Forward Nominal position of the X front screen actuator which ensures that correspond-
ing stencil and board fiducials can be viewed from a single camera position.
Screen X Rear Nominal position of the X rear screen actuator which ensures that correspond-
ing stencil and board fiducials can be viewed from a single camera position.
Screen Y Axis Nominal position of the Y screen actuator which ensures that corresponding
stencil and board fiducials can be viewed from a single camera position.
Alignment
Weighting
This is only used in 2 fiducial mode and sets a value determining how much of
the fiducial spacing error is assigned to fiducial 2.
X Align Weighting This is only used in 3 fiducial mode and sets a value determining where the X
axis alignment should be optimized.
Minimum Maximum Increment
-1.0mm +1.0mm 0.004mm
Minimum Maximum Increment
-1.0mm +1.0mm 0.004mm
Minimum Maximum Increment
-1000 arc seconds +1000 arc seconds 2 arc seconds
Minimum Maximum Increment
-20.0mm +20.0mm 0.004mm
Minimum Maximum Increment
-20.0mm +20.0mm 0.004mm
Minimum Maximum Increment
-10.0mm +10.0mm 0.004mm
Minimum Maximum Increment Default
0% 100% 1% 50% (see vision system)
Minimum Maximum Increment Default
0% 100% 1% 50% (see vision system)
0$&+,1(352*5$00,1*
0(183$5$0(7(56
1.114 User Manual Software Version 07SP04
Y Align Weighting This is only used in 3 fiducial mode and sets a value determining where the Y
axis alignment should be optimized.
Alignment Mode This parameter determines the mode used for board to stencil alignment. The
Non Vision option is only available from the configuration file. Options available
are:
Tooling Type This determines which type of board support is to be used with this particular
product. Options are:
NOTE
Vac for Flex is only available while Feature License Authentication asserts that
Flexible Board Printing is permitted.
Vacuum Sensor
Delay
This parameter determines the length of time after the vacuum tooling has been
switched on before the vacuum sensor is checked, to allow a vacuum seal to
be achieved.
NOTE
This parameter is only available if Tooling Type is set to Vacuum.
Flatten Vacuum
Delay
This parameter determines the duration of vacuum applied whilst the board is
pressed against the underside of the stencil with Vac for Flex enabled.
Separation
Vacuum Delay
This parameter determines the duration of vacuum applied after printing and
before the rising table is lowered to separation height with Vac for Flex enabled.
Minimum Maximum Increment Default
0% 100% 1% 50% (see vision system)
Options Available Default
2 Fiducial 2 Fiducial
3 Fiducial
Options
Vacuum
Magnetic Pillars
AutoFlex
Vac for Flex
Minimum Maximum Increment Default
0.1 sec 3.0 secs 0.1 sec 1.5 secs
Minimum Maximum Increment Default
0 sec 5 secs 0.1 sec 2 secs
Minimum Maximum Increment Default
0 sec 5 secs 0.1 sec 2 secs