Printer 600 Machine Programming.pdf - 第89页
0$&+,1 (352*5$0 0,1* 67$*( 35,17,1 58102'( Software Version 07SP04 User Manual 1.89 screws che cking t hat the 0.25mm gap r emains. 9. Repeat S teps 7 and 8 for the other def lector . 10. Either: a. Clo…
0$&+,1(352*5$00,1*
67$*(35,17,158102'(
1.88 User Manual Software Version 07SP04
STAGE 9 - PRINT IN RUN MODE
1. Select Setup (F6).
2. Select Mode (F1) until Auto is indicated in the mode option on the monitor.
3. Select Exit (F8).
4. Select Run (F1). If squeegees are being used continue with Step 5, if
ProFlow is being used go to Step 20.
5. During the first print stroke, when the squeegee is down printing on the
board, select Stop Cycle (F2). The print cycle stops and the printer lid bolt
releases allowing access to the print carriage.
6. Either:
a. Open the front printhead cover.
or
b. Raise the printhead shutter and lower the drop down panel.
7. Release the screws holding one paste deflector allowing it to drop into
contact with the stencil.
8. Insert a 0.25mm feeler between the deflector and the stencil. Tighten the
Run
Open
Cover
Paste
Load
Clean
Screen
Adjust Setup Monitor Maint.
Mode
Load
Data
Edit
Data
Setup
Squeegee
Change
Screen
Change
Tool ing
Change
Language
Exit
Mode
Load
Data
Edit
Data
Setup
Squeegee
Change
Screen
Change
Tool ing
Change
Language
Exit
Run
Open
Cover
Paste
Load
Clean
Screen
Adjust Setup Monitor Maint.
End
Run
Stop
Cycle
Paste
Load
Clean
Screen
Adjust
Knead
Paste
Adjust
Inspect
0$&+,1(352*5$00,1*
67$*(35,17,158102'(
Software Version 07SP04 User Manual 1.89
screws checking that the 0.25mm gap remains.
9. Repeat Steps 7 and 8 for the other deflector.
10.Either:
a. Close the front printhead cover.
or
b. Raise the drop down panel and lower the printhead shutter.
11. Press the System button.
12.Select Continue (F1).
13.After the squeegee has moved approximately 20mm, select Stop Cycle
(F2).
14.Either:
a. Open the front printhead cover.
or
b. Raise the printhead shutter and lower the drop down panel.
15.Check the deflectors are not touching the stencil.
16.Either:
a. Close the front printhead cover.
or
b. Raise the drop down panel and lower the printhead shutter.
17.Press the System button.
18.Select Continue (F1).
Continue
End
Run
Stop
Cycle
Paste
Load
Clean
Screen
Adjust
Knead
Paste
Adjust
Inspect
Continue
0$&+,1(352*5$00,1*
67$*(35,17,158102'(
1.90 User Manual Software Version 07SP04
19.Repeat Steps 5-18 for the other squeegee.
20.The printer operates continuously. The menu bar displays the following
options, these may be selected at any time during a print run:
End Run Selecting this option stops the printer on completion of the current print cycle.
Stop Cycle Selecting this option stops the printer immediately, halting all actions.
Paste Load Selecting this option allows the operator to load paste to the stencil either
manually or automatically.
Clean Screen Selecting this option allows the operator to clean the stencil in addition to the
programmed cleaning intervals.
Adjust Selecting this option allows the operator to adjust any of the main process
parameters displayed on the pop-up menu without having to access the main
menu or stop the machine.
The machine continues to run using the existing values, when Exit (F8) is
selected the new values are used.
To save the new values, select Setup (F6), select Edit Data (F3), select Save
(F2), select Exit (F8).
Knead Paste Selecting this option runs the knead paste process in addition to the pro-
grammed cleaning intervals.
Adjust Inspect Selecting this option allows the operator to edit 2D inspection parameters.
NOTE
Global Limits, Limit Sets and Site parameters can be edited. Site coordinates
can not be adjusted. Any changes made to inspection parameters are saved
on exit.
End
Run
Stop
Cycle
Paste
Load
Clean
Screen
Adjust
Knead
Paste
Adjust
Inspect