Printer 600 Machine Programming.pdf - 第103页
0$&+,1 (352*5$0 0,1* 0(18 3$5 $0( 7(5 6 Software Version 07SP04 User Manual 1.103 the end of the under screen cleaner s troke. Opt ions are: Print Deposi t s This para meter set s t he number of con secutiv e print…
0$&+,1(352*5$00,1*
0(183$5$0(7(56
1.102 User Manual Software Version 07SP04
Separation Speed This parameter sets the speed at which the rising table drives down the
separation distance.
Separation
Distance
This parameter sets the separation distance between board and stencil. The
parameter can help increase cycle time when a low separation speed is used
by decreasing the separation distance.
Board Count This function provides the facility for the print cycle to be halted automatically
on a board count basis.
If the board stop count is zero this function is not active. When a print run is
started, a count is made from the STOP CYCLE AFTER value to zero decre-
menting by one for each board printed.
When the counter reaches zero, the print cycle is finished and control returned
to the main display page and the beacon is set to amber, thus indicating that the
machine requires operator attention.
The operator has access to all of the machines options. Once the operator has
performed any required operations, the run button can be pressed to continue
the print cycle.
Separation Delay This parameter is the time in seconds that the table delays before lowering. This
delay occurs during screen cleaning and after the flood. This parameter only
becomes available when Adhesive has been selected in the Print Mode
parameter.
Print Mode This parameter sets the mode of operation of the machine. Available modes
are:
Paste Ridge
Removal
This parameter enables the cleaning option Paste Ridge Removal. This option
removes the ridge of paste that can develop on the underside of the stencil at
Minimum Maximum Increment
0.1mm/sec 20.0mm/sec 0.1mm/sec
Minimum Maximum Increment Default
0.0mm 3.0mm 0.1mm 3.0mm
Minimum Maximum Increment
0 Boards 500 Boards 1 Board
Modes Available Note Default
Print / Print Print / Print
Print / Flood
Flood / Print
Adhesive Selecting Adhesive from this parameter
opens the separation delay and print vacuum
mode
0$&+,1(352*5$00,1*
0(183$5$0(7(56
Software Version 07SP04 User Manual 1.103
the end of the under screen cleaner stroke. Options are:
Print Deposits This parameter sets the number of consecutive print strokes carried out on one
substrate.
Print Vacuum
Mode
This parameter determines the state of the vacuum during the print and flood
stages of the cycle. The parameter is only available if Adhesive has been
selected in the Print Mode parameter.
Paste Dispense
Rate
This parameter sets the number of print cycles which occur between cycling of
the paste dispense system.
Paste Dispense
Speed
This parameter sets the speed at which the paste dispenser moves across the
stencil thereby determining the amount of paste deposited on the stencil.
Paste While Clean This parameter enables the machine to carry out a paste dispense while
cleaning the stencil. Available modes are:
Paste With Board This parameter gives the option to dispense paste with a board loaded and held
at print height. This prevents paste dropping through the image on the stencil,
options are:
Option Default
Disabled Disabled
Enabled
Select Default
11
2
3
Mode
ON
OFF
Minimum Maximum Increment
0 (Dispenser switched off) 100 1
Minimum Maximum Increment
10.0mm/sec 100.0mm/sec 1.0mm/sec
Mode
Disabled
Mode 1
Mode 2
Both Modes
0$&+,1(352*5$00,1*
0(183$5$0(7(56
1.104 User Manual Software Version 07SP04
NOTE
With enabled selected the parameter Paste While Clean is removed.
Alternate Disp This parameter gives the option to dispense at either ENDS or CENTRE. ENDS
dispenses at the outer 25% of the squeegees. CENTRE dispenses along an
area of 25% either side of the centre line.
Alternate Disp
Rate
This parameter enables the user to select the ratio of alternate dispenses to
standard dispenses.
Paste Recovery
Rate
This parameter sets the frequency, measured in print strokes completed in
either direction, at which paste roll recovery occurs in both directions, when
using squeegees.
Front Paste
Recovery
This parameter sets the extent of paste roll recovery movement while beginning
the rearward print stroke. The movement is measured forward from the print
stroke start position.
Rear Paste
Recovery
This parameter sets the extent of paste roll recovery movement while beginning
the forward print stroke. The movement is measured rearward from the print
stroke start position.
Screen Clean
Mode 1 (including
Vacuum)
This parameter sets the mode of operation of the screen cleaner for the first
clean mode. When selected this parameter opens a window that allows a
screen clean option sequence to be chosen. The sequence includes six stages,
Options Available
Enabled
Disabled
Options Available
Ends
Centre
No Alternate Dispense Every Dispense Every Second Dispense etc.
Minimum Maximum Increment Default
0
(This disables paste
roll recovery)
500 1 1
Minimum Maximum Increment Default
0.0mm 15.0mm
(Subject to front turn-
around envelope)
1.0mm 5.0mm
Minimum Maximum Increment Default
0.0mm 15.0mm
(Subject to rear turn-
around envelope)
1.0mm 5.0mm