OM-1076-001.pdf - 第37页

(13) Nozzle Change Select one of the following options to designate the rate of the nozzle change speed reduction when a component is picked up. Full Speed 10% Decr 20% Decr 30% Decr 40% Decr 50% Decr 60% Decr 70% Decr 8…

(10) Pl Descent Dclr 2 Stroke [mm]

Set a parameter to designate the stroke in the data box so that the X/

Y beam descends along with the stoke and at a very slow speed (speed

reduction specified in the "Pl descent dclr 2").

Unit: mm

Data Input Range: 1.00 to 5.00

A02 Control Data (A02_01)

0206-002 2-18 Tg0502-PM-CL

Fig.B22

Pl descent dclr 2 stroke [mm]

1.00

Use this function when a press-fit or insertion component must be placed.

(11) Pl Ascent

Select one of the following options to designate the rate of the head

ascending speed reduction after the component placement.

Full Speed 10% Decr 20% Decr 30% Decr 40% Decr

50% Decr 60% Decr 70% Decr 80% Decr 90% Decr

(12) Nozzle Rotation

Select one of the following options to designate the rate of nozzle

rotation speed reduction when a component is picked up.

Full Speed 10% Decr 20% Decr 30% Decr 40% Decr

50% Decr 60% Decr 70% Decr 80% Decr 90% Decr

Fig.B25

Nozzle rotation Full Speed

Fig.B24

Pl ascent Full Speed

Nozzle

Component

Reflection of "Pl Descent Dclr 1"

Reflection of "Pl Descent Dclr 2"

"Pl Descent Dclr 2 Stroke"

Pass Line

(Lower or Upper Pass Line)

Side View

Fig. B23

(13) Nozzle Change

Select one of the following options to designate the rate of the nozzle

change speed reduction when a component is picked up.

Full Speed 10% Decr 20% Decr 30% Decr 40% Decr

50% Decr 60% Decr 70% Decr 80% Decr 90% Decr

(14) Recognition Time [sec] (Disable)

Set the approximate time required for component recognition process-

ing in the data box.

Unit: second

Data Input Range: 0.00 to 9.99

This set parameter is used to process the optimization.

(15) Pu Retention Time [sec]

Set the retention time for the nozzle at the lower limit when a compo-

nent is picked up.

Unit: second

Data Input Range: 0.00 to 1.99

This function can be used when the pick-up is not stable due to the influ-

ence of the component pick-up surface or some incompatibility with the

nozzle.

(16) Pl Retention Time [sec]

Set the retention time for the nozzle at the lower limit when a compo-

nent is placed.

Unit: second

Data Input Range: 0.00 to 1.99

A02 Control Data (A02_01)

0111-002 2-19 Tg0502-PM-CL

Fig.B26

Nozzle change

Full Speed

Fig.B27

Recognition time [sec]

0.00

Fig.B28

Pu retention time [sec]

0.00

Fig.B29

Pl retention time [sec]

0.00

(17) Cmpnt Detection (Sensor)

Set whether to judge the pick-up quality with the vacuum sensor.

"DISABLE" or "ENABLE" can be selected.

When the nozzle selected in "Selected NOZZLE" meets one of the re-

quirements described in the table below, "DISABLE" is selected auto-

matically.

Table B11

(18) Air blow

From the following items, select whether or not to air blow when the

component is placed.

Enable Disable

(19) Air blow off timing [mm]

Set the position at which the air blow is turned off.

This function is used when the nozzle error occurs where component

is brought back.

Unit: mm

Data Input Range: 0.0 to 9.9

A02 Control Data (A02_01)

0206-003 2-20 Tg0502-PM-CL

Fig.B30

Cmpnt detection (Sensor)

Disable

Fig.B30-1

Air blow

Enable

Fig.B30-2

Air blow off timing [mm]

0.0

Fig. B30-3

Item Condition Remarks

Nozzle ID EC** Mechanical Chuck Nozzle

EE** Mechanical Chuck Nozzle

Area of Pick-Up Hole Less then 0.7854mm

Total Area of Pick-Up Hole