00196962-04-BA-SX12-V2-EN.pdf - 第261页
User manual SIPLACE SX1/SX2 5 Working with the machine From software version SC 706.1 SP1 Version 10/2014 5.10 Setting up the feeder modules 261 5 Close the pickup window (i tem 3 in fig. 5.10 - 2 ), by returning the l…
5 Working with the machine User manual SIPLACE SX1/SX2
5.10 Setting up the feeder modules From software version SC 706.1 SP1 Version 10/2014
260
The X feeder module is locked in position in the changeover table by a latch, and cannot be pulled
out. The procedure for removing feeder modules from the changeover table is as follows:
Press the removal handle (item 1 in fig. 5.10 - 1, page 259). The removal handle jumps
out and the status display goes out.
Wait approximately 1 second until the lock (item 4 in fig. 5.10 - 1, page 259) releases the
feeder module.
Use the removal handle to pull the feeder module out of the changeover table. If you wait
longer than 5 seconds, the feeder module will be locked once more. The status display
lights up red and the message (item 3 in fig. 5.10 - 1
, page 259) "Handle --->>" appears
on the LCD display.
Engage the removal handle once more. If the X feeder module is contained in the current
setup, the status display lights up green and the track number and increment are appear
on the LCD display once more.
Press the removal handle again (item 1 in fig. 5.10 - 1, page 259) and now pull the feeder
module out of the changeover table.
5.10.3 Using the X feeder module
5.10.3.1 Check the X feeder module before using it
Check the following points before you use a feeder module on the changeover table:
The feeder module must be in perfect condition.
Tap the cover foil rocker (item 2 in fig. 5.10 - 2, page 262) lightly to make sure that it has
not
jammed.
Check that the area around the pickup window (item 3 in fig. 5.10 - 2, page 262) is free
from loose components.
5
Press the lever (item 4 in fig. 5.10 - 2, page 262) forward slightly to open the pickup win-
dow (item 3 in fig. 5.10 - 2
, page 262). This will raise the pick-up window slightly.
5
PLEASE NOTE
Empty the component disposal compartment (item 5 in fig.5.10 - 2, page 262), before
you
shake components out of the feeder module.
PLEASE NOTE
The tensioned cover foil continues to transport the tape when the tape has been inserted
and exposes the components.
Do not press the lever if a component tape is inserted.
User manual SIPLACE SX1/SX2 5 Working with the machine
From software version SC 706.1 SP1 Version 10/2014 5.10 Setting up the feeder modules
261
5
Close the pickup window (item 3 in fig. 5.10 - 2), by returning the lever (item 4 in fig. 5.10
- 2) to its original position.
Remove loose components from the changeover table with a brush or use a vacuum
cleaner with appropriate nozzle.
5
If the removal handle (item 1) is still protruding, then latch it in place.
PLEASE NOTE
If the component tape is already inserted, cut it off flush with the front edge of the
feeder module.
5 Working with the machine User manual SIPLACE SX1/SX2
5.10 Setting up the feeder modules From software version SC 706.1 SP1 Version 10/2014
262
5
Fig. 5.10 - 2 Check the X feeder module before using it
(1) Removal handle
(2) Cover foil rocker
(3) Pickup window
(4) Lever for raising and latching the pick-up window
(5) Component disposal compartment