3OM-1064-001.pdf - 第11页

V acuum Pressure System Check whether the vacuum pressure is correctly adjusted. *1 Set the operation mode to “PLACE” by pressing the [P ASS/PLACE CHANGE] key at the “AUT O OPN. SUB-MENU” display and turn off all vacuum …

WARNING

•

In principle, the machine should be operated

by only one person for troubleshooting.

If there are more than one, ensure good com-

munication by giving loud verbal instructions.

•

Troubleshoot the machine carefully, protect-

ing your hands from moving mechanisms

when the machine is powered up.

•

When the [OPERATION/SET UP] switch is

set to the "SET UP" side, it becomes pos-

sible to operate the machine with the main-

tenance cover open. Be sure to pay a spe-

cial caution while operating the machine.

1. Cause and Remedy of Simple Trouble

0005-002 1-2 Tg0248-PM-ER

Table 1.1

1. Cause and Remedy of Simple Trouble

Trouble Cause Remedy

• The power breaker crank

is kept OFF (

{

• Set the power breaker crank to “ON” ( ).

• Power is not supplied to

the connection terminal of

the primary power supply

unit.

• Supply power to the connection terminal

of the primary power supply unit.

Although the [POWER

ON] button on the

operation panel is pressed,

power is not supplied.

• Adequate air pressure is

not set.

• Check the air pressure.

Main Pressure:

0.49 MPa (5 kgf/cm

)

Air Blowing Pressure:

0.015 MPa (0.15 kgf/cm

)

Pressure Switch:

0.39 MPa (4 kgf/cm

)

• The air source cock is

closed.

• Open the air source cock.

The main pressure is “0

(zero)”.

• Air does not reach the air

source cock.

• Check the air hose, etc.

• Power is not supplied. • Power up the machine as follows.

Set the power breaker crank to “ON” ( ).

Press and hold the [POWER ON] button

on the operation panel for more than 1

second.

Nothing is displayed on the

touch screen.

• The screen saver function

is activated.

• Touch the screen.

The operation panel and

the touch screen are un-

available for operation.

• Operation availability is

locked on the opposite

side.

• (The operation lock

(HD06) lamp is ON.)

• Press the [PNL CHANGE] button on the

opposite side and press the same button on

the other side (on the panel to be oper-

ated).

Vacuum Pressure System

Check whether the vacuum pressure is correctly adjusted. *1

Set the operation mode to “PLACE” by pressing the [PASS/PLACE

CHANGE] key at the “AUTO OPN. SUB-MENU” display and turn

off all vacuum valves ([LA1-AXIS VACUUM/VACUUM BLOW],

[LA2-AXIS VACUUM/VACUUM BLOW], [LB1-AXIS VACUUM/

VACUUM BLOW], and [LB2-AXIS VACUUM/VACUUM BLOW]

Keys).

Confirm that “OFF” is set in the “STATUS” text boxes at the

“MANUAL SUBSYSTEM OPERATION” display.

Confirm that the vacuum pressure is -93 kPa (70 cmHg) or more

(Vacuum valve fully closed).

When the vacuum pressure is too low, it is required to replace the

vacuum pump with a new one.

Consult our sales personnel for the detailed information on how to

replace or repair the vacuum pump.

Check whether the vacuum pump is producing any abnormal sound. *2

Catch the sound of the vacuum pump and confirm that the sound is

not abnormal.

When abnormal sound is produced, consult our sales personnel for

the countermeasures.

Check whether the filter of the vacuum pump is stained or clogged.

Refer to “Vacuum Pressure System” in “8. Maintenance (Every 3

Months) of Section 1 in Volume 4” and inspect the filter.

1.1 Confirmation and Countermeasures against Low

Component Pick-Up Rate

1.1.1 Confirmation of Low Component Pick-Up Rate (Handling

Errors)

• Before confirming each item, check the following management information

and grasp the contents, the frequency, and the trend of pick-up errors.

(1) Machine Performance Data and Component Pick-Up/Placement In-

formation in Management Data

(2) Nozzle Management Data in Management Data

(3) Head Management Data in Management Data

(4) Handling Error per Feeder Location in Pattern Program Management

Data

(5) Recall Handling Error

(6) Recall Component Recognition Error

Refer to “4. RECALL MESSAGES of Section 3 in Volume 4” for the de-

tailed information on (1) through (4).

Refer to “3. MANAGEMENT DATA Display of Section 3 in Volume 4”

for the detailed information on (5) and (6).

1.1.2 Countermeasures against Frequent Pick-Up Errors

0005-002 1-3 Tg0248-PM-ER

1. Cause and Remedy of Simple Trouble

Placement Head

Check whether the vacuum filter of the placement is stained or

clogged. *4

Refer to “Head” in “6. Monthly Maintenance of Section 1 in Volume

4” and inspect the filter. If necessary, replace the filter with a new

one.

Check whether the internal part of the vacuum nozzle is stained

or clogged. *5

Refer to “Nozzle Stocker” in “6. Monthly Maintenance of Section 1

in Volume 4” and inspect the nozzles. If necessary, clean them.

Check whether the solenoid valves for vacuum and blowing are

correctly changed over. *6

Follow the two check procedures described below.

Items Required for Confirmation

• MA04 Nozzle

• Small Piece of Paper (Approx. 10 × 10 mm)

Notes: (a) Sebum nor oil, etc., should not adhere to the surface

of the diffusion plate of the vacuum nozzle.

(b) Detach the feeder before confirmation.

Procedure for Confirmation (Air Supply: “OFF”)

(1) Open the “ZEROING OPERATION” display and zero the X/Y

beam. (Hierarchical Sequence: “MANUAL MODE” Display

→ “ZEROING OPERATION” Display)

(2) Open the “MANUAL NOZZLE CHANGE OPERATION” dis-

play and replace the vacuum nozzle (the nozzle of the place-

ment head to be checked) with the MA04 one. (Hierarchical

Sequence: “MANUAL MODE” Display → “MANUAL

NOZZLE CHANGE OPERATION” Display)

(3) Open the “MANUAL SUBSYSTEM OPERATION” display.

Select the [BEAM-A AIR SUPPLY] or the [BEAM-B AIR SUP-

PLY] key and press the [MOVE] button to set to “OFF”. (Hier-

archical Sequence: “MANUAL MODE” Display → “MANUAL

SUBSYSTEM OPERATION” Display)

(4) Open the “MANUAL AXIS OPERATION” display and move

the X/Y beams until they can be reached by hands. (Hierarchi-

cal Sequence: “MANUAL MODE” Display → “MANUAL

AXIS OPERATION” Display)

(5) Set the [OPERATION/SET UP] switch on the checked side to

the “SET UP” side.

(6) Press the [READY ] button on the checked side and release the

electromagnetic locks of the supply cover and the safety bar.

(7) Open the supply cover on the checked side.

(8) Open the “MANUAL SUBSYSTEM OPERATION” display and

press the [L**-AXIS VACUUM/BLOW] key to set the “BLOW”

mode. (Hierarchical Sequence: “MANUAL MODE” Display →

“MANUAL SUBSYSTEM OPERATION” Display)

(9) Put a small piece of paper on your palm and bring it close to the

end of the vacuum nozzle. Confirm that the paper does not move

at all.

Confirm that the paper is picked up when the [L**-AXIS

VACUUM/BLOW] key is pressed again to set the

“VACUUM”mode.

Cut out the portion above

to use. (10

× 10 mm)

1. Cause and Remedy of Simple Trouble

0005-002 1-4 Tg0248-PM-ER