3OM-1064-001.pdf - 第224页

A P ARAMETER OTHER THAN “90°INCR” IS SET AS “LIN- EAR EDGE DIRECTION”. 3. Control-to-Control Communication Error Code and List of Error Messages 0009-003 4-28 Tg0248-PM-ER Error Code Display A Display B 1 1364000 TRANSFE…

100%1 / 308
3. Control-to-Control Communication Error Code and List of Error Messages
0009-003 4-27 Tg0248-PM-ER
Error Code Display A Display B
11360001 TRANSFERRING THE COM-
PONENT RECOGNITION DATA
UNABAILABLE RECOGNITION IN CAMERA WITH MA-
CHINE BECAUSE “OUTWARD LENGTH” IS BIG.
11360002 TRANSFERRING THE COM-
PONENT RECOGNITION DATA
11360003 TRANSFERRING THE COM-
PONENT RECOGNITION DATA
UNAVAILABLE RECOGNITION IN CAMERA WITH MA-
CHINE BECAUSE “LEAD PITCH” IS SMALL.
11360004 TRANSFERRING THE COM-
PONENT RECOGNITION DATA
UNAVAILABLE RECOGNITION IN CAMERA WITH MA-
CHINE BECAUSE “BALL DIAMETER” IS SMALL.
11360000 TRANSFERRING THE COM-
PONENT RECOGNITION DATA
UNABAILABLE RECOGNITION IN CAMERA WITH MA-
CHINE BECAUSE “OUTWARD LENGTH” IS SMALL.
11360005 TRANSFERRING THE COM-
PONENT RECOGNITION DATA
UNAVAILABLE RECOGNITION IN CAMERA WITH MA-
CHINE BECAUSE “BALL PITCH” IS SMALL.
11360006 TRANSFERRING THE COM-
PONENT RECOGNITION DATA
ALL CAMERAS ARE CANCELED DUE TO THE PARAM-
ETER SET FOR “VIEW RANGE SET”.
UNAVAILABLE RECOGNITION IN CAMERA WITH MA-
CHINE BECAUSE “LEAD WIDTH” IS SMALL.
(Cause 1) This is the device’s self-diagnostic message.
(Reset Procedure in the case of Cause 1)
Reset Procedure
(1) Press the [CLEAR ALARM] key and the buzzer stops sounding.
(2) Press the [ZERO] button to return all the axes to their original positions.
(3) Re-start.
(4) If the device can’t be re-started, contact our service personnel.
11360007 TRANSFERRING THE COM-
PONENT RECOGNITION DATA
POLARITY CANNOT BE DETECTED BECAUSE
“OUTWARD LENGTH” IS BIG.
11360008 TRANSFERRING THE COM-
PONENT RECOGNITION DATA
“FLUX DIP & MOUNT” IS SET AS MOUNT MODE BUT
THERE IS NOT MIN VIEW CAMERA WITH MACHINE.
A PARAMETER OTHER THAN “90°INCR” IS SET AS “LIN-
EAR EDGE DIRECTION”.
3. Control-to-Control Communication Error Code and List of Error Messages
0009-003 4-28 Tg0248-PM-ER
Error Code Display A Display B
11364000 TRANSFERRING THE COM-
PONENT RECOGNITION DATA
“DISABLE” IS SET FOR ALL CORNER FORMS 1 TO 4.
11364001 TRANSFERRING THE COM-
PONENT RECOGNITION DATA
A PARAMETER OTHER THAN “STRAIGHT” IS SET FOR
ALL EDGE FORMS 1 TO 4.
11365000 TRANSFERRING THE COM-
PONENT RECOGNITION DATA
“LEAD WIDTH” IS LARGER THAN “LEAD PITCH”.
11365001 TRANSFERRING THE COM-
PONENT RECOGNITION DATA
“MISSING LEAD START” IS LARGER THAN “# OF LEADS
+1”.
11365002 TRANSFERRING THE COM-
PONENT RECOGNITION DATA
11365003 TRANSFERRING THE COM-
PONENT RECOGNITION DATA
THE PARAMETER SELECTED FOR “RECOGNITION
LIGHTING MODE” DOES NOT CONFORM TO THE PA-
RAMETER SET FOR “LEAD FORM”.
11365004 TRANSFERRING THE COM-
PONENT RECOGNITION DATA
11365005 TRANSFERRING THE COM-
PONENT RECOGNITION DATA
“LEAD FULL LENGTH” IS NOT SET.
11367000 TRANSFERRING THE COM-
PONENT RECOGNITION DATA
“BALL DIAMETER” IS LARGER THAN “BALL PITCH”.
11367001 TRANSFERRING THE COM-
PONENT RECOGNITION DATA
“MISSING BALL START” IS LARGER THAN “# OF BALL”.
11368000 TRANSFERRING THE COM-
PONENT RECOGNITION DATA
AN UNREGISTERED LEAD TYPE NO. IS SELECTED.
11368001 TRANSFERRING THE COM-
PONENT RECOGNITION DATA
A PARAMETER OTHER THAN “90°INCR” IS SET AS
“LEAD GROUP DIRECTION”.
11369000 TRANSFERRING THE COM-
PONENT RECOGNITION DATA
“LEAD LENGTH” IS LARGER THAN “LEAD FULL
LENGTH”.
“LEAD LENGTH” IS NOT SET.
(Cause 1) This is the device’s self-diagnostic message.
(Reset Procedure in the case of Cause 1)
Reset Procedure
(1) Press the [CLEAR ALARM] key and the buzzer stops sounding.
(2) Press the [ZERO] button to return all the axes to their original positions.
(3) Re-start.
(4) If the device can’t be re-started, contact our service personnel.
11367002 TRANSFERRING THE COM-
PONENT RECOGNITION DATA
“INSPECTION RANGE” IS OUT OF COMPONENT SIZE.
11367003 TRANSFERRING THE COM-
PONENT RECOGNITION DATA
“# OF BALLS” IS TOO SMALL.
11367004 TRANSFERRING THE COM-
PONENT RECOGNITION DATA
THOSE BALLS OVERLAPPED.
11367006 TRANSFERRING THE COM-
PONENT RECOGNITION DATA
“# OF LEADS” IS TOO SMALL.
11367007 TRANSFERRING THE COM-
PONENT RECOGNITION DATA
“# OF LEADS” IS TOO MANY.
3. Control-to-Control Communication Error Code and List of Error Messages
0009-003 4-29 Tg0248-PM-ER
Error Code Display A Display B
11XXXXXX COMMUNICATION DATA
except the ERROR
above-
described
codes
ETC.
12000000 A COMMUNICATION PROCE-
DURE ERROR OCCURRED
AN IMAGE TAKEN BY THE SPECIFIED CAMERA IS NOT
YET RECEIVED.
12000001 A COMMUNICATION PROCE-
DURE ERROR OCCURRED
THE DATA OF THE SPECIFIED NOZZLE IS NOT YET
TRANSFERRED.
12000002 A COMMUNICATION PROCE-
DURE ERROR OCCURRED
THE DATA OF THE SPECIFIED MARK IS NOT YET
TRANSFERRED.
12000003 A COMMUNICATION PROCE-
DURE ERROR OCCURRED
THE DATA OF THE SPECIFIED COMPONENT IS NOT
YET TRANSFERRED.
12XXXXXX A COMMUNICATION PROCE-
except the DURE ERROR OCCURRED
above-
described
codes
ETC.
(Cause 1) This is the device’s self-diagnostic message.
(Reset Procedure in the case of Cause 1)
Reset Procedure
(1) Press the [CLEAR ALARM] key and the buzzer stops sounding.
(2) Press the [ZERO] button to return all the axes to their original positions.
(3) Re-start.
(4) If the device can’t be re-started, contact our service personnel.
(Cause 1) This is the device’s self-diagnostic message.
(Reset Procedure in the case of Cause 1)
Reset Procedure
(1) Press the [CLEAR ALARM] key and the buzzer stops sounding.
(2) Press the [ZERO] button to return all the axes to their original positions.
(3) Re-start.
(4) If the device can’t be re-started, contact our service personnel.
11530000 RECOGNITION ERROR
IMAGE OUTPUT
NOZZLE PROTRUSION PRESENTS ON SOME LEADS.
(Cause 1) This is the device’s self-diagnostic message.
(Reset Procedure in the case of Cause 1)
Reset Procedure
(1) Press the [CLEAR ALARM] key and the buzzer stops sounding.
(2) Press the [ZERO] button to return all the axes to their original positions.
(3) Re-start.
(4) If the device can’t be re-started, contact our service personnel.