00197187-01_AI_LBO_SX12_ab_09-2011_FS02_de_en.pdf - 第51页
Fitting the Long Board Option Installing the Stopper Long Board Option 51 Fitting the stopper ► Dismant le the cover sheet over the installat ion position on the sensor rail. ► Fit the individual pa rts of the s topper t…
Fitting the Long Board Option
Installing the Stopper
50 Long Board Option
► Dismantle the stop rails crossed out in the diagram.
► Fit the lower section of the stopper rail 599L to the left conveyor side for lane 1, using the socket
head cap screws [03042542-xx]. If these screws are missing, use the ones from the old guidance
rails.
► Fit the upper section to the lower section of the stopper rail 599L. Use the filister hex socket head
screws for this [00200240-xx].
► Repeat these steps for the following parts:
Guidance rail AB L [03088179-xx] (left conveyor side for lane 1)
Stopper rail 599R [03088196-xx] (right conveyor side for lane 1)
Guidance rail AB R [03088180-xx] (right conveyor side for lane 1)
► Repeat these steps for lane 2 of the dual conveyor.
3.4 Installing the Stopper
Overview
Stopper connections
1. Connection for "stopper down"
2. Connection for "stopper up"
Installation positions
1. Installation position for stopper
2. Installation position for valve unit
3. Connection cable for valve unit
Fitting the Long Board Option
Installing the Stopper
Long Board Option 51
Fitting the stopper
► Dismantle the cover sheet over the installation position on the sensor rail.
► Fit the individual parts of the stopper to the mounting bracket on the stopper rail, as shown in the
diagram above. Make sure that the sheet is positioned correctly [03084255-xx] (left or right).
Fitting the complete stopper assembly (right shown here)
1. Stopper 25 SX pneumatic complete [03084034-xx]
2. Sheet [03084255-xx] ("right" position shown here)
3. Support socket [03085311-xx]
4. Distance washer M3/H=2 mm [03092259-xx]
5. ISO4762-M3x35-A2-70 socket head cap screw for fit-
ting the stopper [03043114-xx]
6. Spacer LBO [03091992-xx]
7. DIN-EN-ISO7380-M3x25-A2-70 - filister hex socket
head screw [03045198-xx]
8. DIN125-A3,2-140HV-A2 - washer 0.5 mm high
[00316904-xx]
9. Mounting bracket on the sensor rail
1. Stopper with sheet in "left" position for fitting onto the
right conveyor side
2. Stopper with sheet in "right" position for fitting to the
left conveyor side (DT "lane" 2)
Fitting the Long Board Option
Fitting the Valve Unit
52 Long Board Option
3.5 Fitting the Valve Unit
Overview
Fitting the valve unit
► Use the two fastening screws to fit the valve unit in its installation position (4).
► Plug the connection cable (1) into the valve unit.
► Sever the compressed air supply hose (3) at the height of the T-piece (6) of the new valve unit. To
do this, loosen the relevant cable ties. Connect both ends of the severed hose to the T-piece.
► Run all hoses so that they do not rub against anything and are not folded. Fasten them into place
with cable ties.
1. Connection cable for valve unit
2. Neighboring valve unit
3. Compressed air supply hose
4. Installation position for valve unit
5. Valve unit when fitted
6. T-piece on the valve unit
► Connect the left connection on the valve to the lower
connection on the stopper.
► Connect the right connection on the valve to the up-
per connection on the stopper.