4OM-1626-001_w.pdf - 第109页
4OM-1610 2-6 2. Management Information : Chap.2 Management Information Code Display Area A (The outline of the Management Information) Display Area B (The details of the Management Information) 01 170a P .C.B. position P…
4OM-1610
2-5
2. Management Informatio : Chap.2
Management
Information Code
Display Area A (The outline of the Management Information)
Display Area B (The details of the Management Information)
010907 Feeder base conrm (Front)
Feeder base power or Feeder power is "OFF". Please press "Feeder Ready"
switch(Front), and put it up again after putting Feeder Cart(Front) down.
011001 Empty Feeder (rear)
Please set the feeder (rear) that used by the pattern program.
011101 Empty Feeder (front)
Please set the feeder (front) that used by the pattern program.
010b01 Feeder is not ready (rear)
Please turn on the Feeder Ready SW (rear).
010c01 Feeder is not ready (front)
Please turn on the Feeder Ready SW (front).
010d01 Pattern program is abnormal
Please set the normal pattern program
010e01 Prod Chng is not ready
Conveyor width does not t production data.
Execute conveyor width setup.
011401 Zeroing not nish
Perform All zeroing
011402 Zeroing not nish
Perform All zeroing
011403 Zeroing not nish
Perform All zeroing
011404 Zeroing not nish
Perform All zeroing
011405 Zeroing not nish
Perform All zeroing
011406 Motor is not servo on
Perform All zeroing
011701 P.C.B. position
Please position the P.C.B.
011702 P.C.B. position
Set the P.C.B. lower side position.
011703 P.C.B. position
Set the P.C.B. upper side position.
011704 P.C.B. position
Execute P.C.B. position cancel after cancelling operation.
011705 P.C.B. position
Please position P.C.B. [Input or Output] of [Lane A]
011706 P.C.B. position
Please position P.C.B. [Output position] of [Lane A].
011707 P.C.B. position
Please position P.C.B. [Input position] of [Lane A].
011708 P.C.B. position
Please position P.C.B. [Input or Output] of [Lane B].
011709 P.C.B. position
Please position P.C.B. [Output position] of [Lane B].
0911-001
4OM-1610
2-6
2. Management Information : Chap.2
Management
Information Code
Display Area A (The outline of the Management Information)
Display Area B (The details of the Management Information)
01170a P.C.B. position
Please position P.C.B. [Input position] of [Lane B].
011a01 Nozzle stocker lower limit conrmation
Please perform All zeroing.
011c01 Nozzle arrangement conrmation
The nozzle arrangement of the Current Program and the head is different.
012a01 Tray shortage Comp (rear)
Please supply comp, close tray door(rear) and push tray ready SW(Rear).
012b01 Tray shortage Comp (front)
Please supply comp, close tray safety door and push tray ready SW(Front).
013101 Feeder set Err
A pickup miss comp is detected. (Rear)
013102 Feeder set Err
The feeder latch worked off. (Rear)
013103 Feeder set Err
A pickup miss comp is detected. (Front)
013104 Feeder set Err
The feeder latch worked off. (Front)
013105 Feeder set Err
Not connect selected feeder.
013b01 Feeder Ready SW
Please wait stage ready on
013c01 Stage Ready SW
Please wait feeder ready on
013c02 Stage Ready SW
Do not open safety cover while line sensor program updating.
014101 Operation Parameter
Test mode of transfer set "Disable" in pass mode. Check setting.
014102 Operation Parameter
014103 Operation Parameter
014b01 Nozzle Placement Data Check
Set the nozzle ID to use for the No.1 nozzle placement data.
015001 Nozzle Location Check
Not found tting nozzle for calibration.(Rear)
Set type "HA09A" nozzle on Head 1 Nozzle 1.
015002 Nozzle Location Check
Not found tting nozzle for calibration.(Front)
Set type "HA09A" nozzle on Head 2 Nozzle 1.
015003 Nozzle Location Check
Not found tting nozzle for calibration.(Rear)
Set type "HA09A" nozzle on Head 1 Nozzle 1.
015004 Nozzle Location Check
Not found tting nozzle for calibration.(Front)
Set type "HA09A" nozzle on Head 2 Nozzle 1.
0911-001
4OM-1610
2-7
2. Management Informatio : Chap.2
Management
Information Code
Display Area A (The outline of the Management Information)
Display Area B (The details of the Management Information)
015005 Nozzle Location Check
Not found tting nozzle for calibration.(Rear)
Set type "FF01"or "FF02" nozzle on calibrate position.
015006 Nozzle Location Check
Not found tting nozzle for calibration.(Front)
Set type "FF01"or "FF02" nozzle on calibrate position.
015007 Nozzle Location Check
Already set the different type nozzle.(Rear)
Remove it.
015008 Nozzle Location Check
Already set the different type nozzle.(Front)
Remove it.
015009 Nozzle Location Check
Not found tting nozzle for calibration.(Rear)
Set type "FF01"or "FF02" nozzle on calibrate position.
01500A Nozzle Location Check
Not found tting nozzle for calibration.(Front)
Set type "FF01"or "FF02" nozzle on calibrate position.
01500B Nozzle Location Check
Not found tting nozzle for calibration.(Rear)
Set type "VF02" nozzle on calibrate position.
01500C Nozzle Location Check
Not found tting nozzle for calibration.(Front)
Set type "VF02" nozzle on calibrate position.
01500D Nozzle Location Check
Not found tting nozzle for calibration.(Rear)
Set type "HA09A"or "Vf02" nozzle on calibrate position.
01500E Nozzle Location Check
Not found tting nozzle for calibration.(Front)
Set type "HA09A"or "Vf02" nozzle on calibrate position.
01500F Nozzle Location Check
Necessary Noz for teaching does not exist. Please set-up HA09 in the stocker
position in which the nozzle can change.
015010 Nozzle Location Check
Necessary Noz for teaching does not exist. Please set-up HA09 in the stocker
position in which the nozzle can change.
015011 Nozzle Location Check
Necessary Noz for teaching does not exist. Please set-up HA09 in the stocker
position in which the nozzle can change.
015012 Nozzle Location Check
Necessary Noz for teaching does not exist. Please set-up HA09 in the stocker
position in which the nozzle can change.
015101 Nozzle location teaching, check the position of nozzle on head
Could not found nozzle or Could not inspect nozzle (different type ?).
015102 Nozzle location teaching, check on the position of nozzle on head
Could not found or inspect nozzle (different type ?).
0911-001