4OM-1626-001_w.pdf - 第110页
4OM-1610 2-7 2. Management Informatio : Chap.2 Management Information Code Display Area A (The outline of the Management Information) Display Area B (The details of the Management Information) 015005 Nozzle Location Chec…
4OM-1610
2-6
2. Management Information : Chap.2
Management
Information Code
Display Area A (The outline of the Management Information)
Display Area B (The details of the Management Information)
01170a P.C.B. position
Please position P.C.B. [Input position] of [Lane B].
011a01 Nozzle stocker lower limit conrmation
Please perform All zeroing.
011c01 Nozzle arrangement conrmation
The nozzle arrangement of the Current Program and the head is different.
012a01 Tray shortage Comp (rear)
Please supply comp, close tray door(rear) and push tray ready SW(Rear).
012b01 Tray shortage Comp (front)
Please supply comp, close tray safety door and push tray ready SW(Front).
013101 Feeder set Err
A pickup miss comp is detected. (Rear)
013102 Feeder set Err
The feeder latch worked off. (Rear)
013103 Feeder set Err
A pickup miss comp is detected. (Front)
013104 Feeder set Err
The feeder latch worked off. (Front)
013105 Feeder set Err
Not connect selected feeder.
013b01 Feeder Ready SW
Please wait stage ready on
013c01 Stage Ready SW
Please wait feeder ready on
013c02 Stage Ready SW
Do not open safety cover while line sensor program updating.
014101 Operation Parameter
Test mode of transfer set "Disable" in pass mode. Check setting.
014102 Operation Parameter
014103 Operation Parameter
014b01 Nozzle Placement Data Check
Set the nozzle ID to use for the No.1 nozzle placement data.
015001 Nozzle Location Check
Not found tting nozzle for calibration.(Rear)
Set type "HA09A" nozzle on Head 1 Nozzle 1.
015002 Nozzle Location Check
Not found tting nozzle for calibration.(Front)
Set type "HA09A" nozzle on Head 2 Nozzle 1.
015003 Nozzle Location Check
Not found tting nozzle for calibration.(Rear)
Set type "HA09A" nozzle on Head 1 Nozzle 1.
015004 Nozzle Location Check
Not found tting nozzle for calibration.(Front)
Set type "HA09A" nozzle on Head 2 Nozzle 1.
0911-001
4OM-1610
2-7
2. Management Informatio : Chap.2
Management
Information Code
Display Area A (The outline of the Management Information)
Display Area B (The details of the Management Information)
015005 Nozzle Location Check
Not found tting nozzle for calibration.(Rear)
Set type "FF01"or "FF02" nozzle on calibrate position.
015006 Nozzle Location Check
Not found tting nozzle for calibration.(Front)
Set type "FF01"or "FF02" nozzle on calibrate position.
015007 Nozzle Location Check
Already set the different type nozzle.(Rear)
Remove it.
015008 Nozzle Location Check
Already set the different type nozzle.(Front)
Remove it.
015009 Nozzle Location Check
Not found tting nozzle for calibration.(Rear)
Set type "FF01"or "FF02" nozzle on calibrate position.
01500A Nozzle Location Check
Not found tting nozzle for calibration.(Front)
Set type "FF01"or "FF02" nozzle on calibrate position.
01500B Nozzle Location Check
Not found tting nozzle for calibration.(Rear)
Set type "VF02" nozzle on calibrate position.
01500C Nozzle Location Check
Not found tting nozzle for calibration.(Front)
Set type "VF02" nozzle on calibrate position.
01500D Nozzle Location Check
Not found tting nozzle for calibration.(Rear)
Set type "HA09A"or "Vf02" nozzle on calibrate position.
01500E Nozzle Location Check
Not found tting nozzle for calibration.(Front)
Set type "HA09A"or "Vf02" nozzle on calibrate position.
01500F Nozzle Location Check
Necessary Noz for teaching does not exist. Please set-up HA09 in the stocker
position in which the nozzle can change.
015010 Nozzle Location Check
Necessary Noz for teaching does not exist. Please set-up HA09 in the stocker
position in which the nozzle can change.
015011 Nozzle Location Check
Necessary Noz for teaching does not exist. Please set-up HA09 in the stocker
position in which the nozzle can change.
015012 Nozzle Location Check
Necessary Noz for teaching does not exist. Please set-up HA09 in the stocker
position in which the nozzle can change.
015101 Nozzle location teaching, check the position of nozzle on head
Could not found nozzle or Could not inspect nozzle (different type ?).
015102 Nozzle location teaching, check on the position of nozzle on head
Could not found or inspect nozzle (different type ?).
0911-001
4OM-1610
2-8
2. Management Information : Chap.2
Management
Information Code
Display Area A (The outline of the Management Information)
Display Area B (The details of the Management Information)
015201 Teaching check the conveyor
No P.C.B. on Conveyor. Please put P.C.B. in.
015202 Teaching check the conveyor
Please set P.C.B. positioning. Please set it again after cancel positioning if P.C.B.
positioning is already done.
015203 Teaching check the conveyor
016001 Tray teaching
Traverse of Tray is not drawn out (Rear). Draw out Traverse.
016002 Tray teaching
Tray Traverse is not drawn out (Front). Draw out Traverse.
016101 Coplanarity Teaching
"Coplanarity Detection" of Test Operation Mode is set "No". Execute it after
cancelling Test Operation Mode.
016201 Coplanarity Test
Please pickup part.
017009 Teaching Check on the position of Glass jig
Necessary Glass Jig for Teaching does not exist. Please check that Glass Jig is
set in its position.
017201 Nozzle set-up(Rear)
Nozzle Pickup/Store mode of Stocker(Front) is not possible to operate. Please set
Stocker(Rear).
017202 Nozzle set-up(Rear)
High nozzle cannot be stored while Odd nozzle is placed. Please restart after
returning all Odd Nozzle.
017203 Nozzle set-up(Rear)
High nozzle cannot be stored while Odd nozzle is placed. Please restart after
returning all Odd Nozzle.
017204 Nozzle set-up(Rear)
Because of interference with Nozzle which is already placed, it cannot be placed.
Do not place Nozzle in the front and rear of two Odd nozzle placed.
017301 Nozzle set-up(Front)
Nozzle Pickup/Store mode of Stocker(Rear) is not possible. Please set
Stocker(Front).
017302 Nozzle set-up(Front)
High nozzle cannot be stored while Odd nozzle is placed. Please restart after
returning all Odd Nozzle.
017303 Nozzle set-up(Front)
High nozzle cannot be stored while Odd nozzle is placed. Please restart after
returning all Odd Nozzle.
017304 Nozzle set-up(Front)
Because of interference with Nozzle which is already placed, it cannot be placed.
Do not place Nozzle in the front and rear of two Odd nozzle placed.
017401 Button for inserting power
Can not supply power while Line Sensor program is on writing. Operate it after
writing completely.
0911-001