00198142-01_AI_Stationary-Camera-25-33_TX_de_en.pdf - 第54页
Introduction Safety information 1.1.4 Safety In structions for the Compressed Ai r Supp ly 54 Stationary Camera Type 25/33 Stationäre Kamera Typ 25/ 33 1.1.4 1 . 1 . 4 S a f e t y I n s t r u c t io n s f o r t h e C o m…
Introduction
1.1.3 Safety Instructions for the Power Supply (With SMPS) Safety information
Stationary Camera Type 25/33 Stationäre Kamera Typ 25/33 53
Energy state of the machine after switching off at the main power switch
Placement system switched off at the main switch, but still connected
Placement system switched off at the main power switch and disconnected
Compressed air conditions in the machine after switching off at the main switch
When the system is switched off at the main power switch or if the power supply fails, the electrically-
controlled main valve of the compressed air unit closes. The pressure will drop to 0 MPa (0 bar) within
5 seconds.
DANGER
Hazardous voltages in the power supply unit!
The power supply unit houses components (capacitors) that can carry hazardous voltages for
about 5 minutes after the machine has been switched off and the power plug has been un
-
plugged.
► Wait at least 5 minutes before your start working on the power supply unit.
► Work on the power supply and the contactor safety breaker (CSB) must only be carried out
by service engineers of ASM Assembly Systems GmbH & Co. KG or by machine owner ser
-
vice engineers who have been trained by ASM.
CAUTION
Loss of data!
To avoid losing data, assess the following criteria before switching off your automatic place
-
ment system (apart from in emergencies):
► Has the placement system finished transmitting machine, setup and panel data?
► Has the placement system finished processing the PCB?
► Has the placement system completed the run-up phase?
DANGER
Risk of death by voltages!
Incorrect handling of the placement system can result in death or severe injury or considerable
damage to equipment.
The following components still carry potentially lethal voltages on the power supply even if the
main power switch is switched off:
► Main power supply cable connection terminals
► L1, L2, and L3 of the main switch S1
► Service socket X98
► Contactor safety breaker (CBS) still carries voltage for 5 minutes after switching off at the
main switch.
► The color of all individual wires which still carry potentially lethal voltages even if the main
power switch is switched off is orange.
DANGER
Hazardous voltages in the power supply unit!
The power supply unit houses components (capacitors) that can carry hazardous voltages for
about 5 minutes after the machine has been switched off and the power plug has been un
-
plugged.
► Wait at least 5 minutes before your start working on the power supply unit.
► Work on the power supply and the contactor safety breaker (CSB) must only be carried out
by service engineers of ASM Assembly Systems GmbH & Co. KG or by machine owner ser
-
vice engineers who have been trained by ASM.
Introduction
Safety information 1.1.4 Safety Instructions for the Compressed Air Supply
54 Stationary Camera Type 25/33 Stationäre Kamera Typ 25/33
1.1.4
1.1.4 Safety Instructions for the Compressed Air Supply
Safety Instructions for the Compressed Air Supply
Risk of injury from compressed air
Prolonge d interruptions to the compr essed air supply can cause d amage
1.1.5
1.1.5 Safety Instructions for Work on the Cutting Device
Safety Instructions for Work on the Cutting Device
Safety Instruc tions for Work o n the Cutting D evice
Risk of injury when working near the tap e cutter
Risk of injury when performing service work on the tape cutter
1.1.6
1.1.6 Safety Instructions for the Gantry
Safety Instructions for the Gantry
CAUTION
Risk of injury from compressed air!
Risk of injury when disconnecting the compressed air lines.
► NEVER disconnect compressed air lines while they are still pressurized.
CAUTION
Prolonged interruptions to the compressed air supply can cause damage.
When the machine is switched on, do not use the shutoff valve to interrupt the compressed air
supply for more than 30 minutes.
► If you need to shut off the compressed air system for longer in order to carry out your work,
you must switch the placement system off at the main switch and disconnect it from the
power supply.
WARNING
Risk of injury when working near the cutter.
When working in the area of the tape cutter, move the component trolley out of the machine
and disconnect the machine from the mains supply and the compressed air supply.
► Wait until the operating pressure has dropped to 0 MPa.
► Always secure the machine against unauthorized reactivation.
► Do not reach into the tape cutter.
CAUTION
Risk of injury when performing service work on the tape cutter.
Never support the tape cutter on your body, e.g., on your knees or thighs. Do not place your
feet under the tape cutter.
► Wear appropriately thick protective gloves.
► When removing/fitting the tape cutter, hold it only on the left and right, on the outside.
CAUTION
Moving the gantry can damage the placement head.
When moving the gantry, observe the following:
► NEVER move the gantry by pushing with your hands against the placement head.
► NEVER push the gantry while the Z axis is lowered.
Introduction
1.1.7 Classification of the Optical Systems Safety information
Stationary Camera Type 25/33 Stationäre Kamera Typ 25/33 55
1.1.7
1.1.7 Classification of the Optical Systems
Classification of the Optical Systems
1.1.7.1
1.1.7.1 Classification of the Whole Machine
Classification of the Whole Machine
1.1.7.2
1.1.7.2 Laser Classification
Laser Classification
The following modules are assigned to the laser class 2:
▪ PCB barcode scanner
▪ Component sensor on the SpeedStar
▪ Component sensor on the MultiStar
▪ Laser light barriers at the board conveyor
1.1.7.3
1.1.7.3 Classification of the Camera Systems
Classification of the Camera Systems
Laser Class 2 label
The ready-to-operate overall machine is assigned to
laser class 2.
The laser classes are determined according to DIN
EN 60825-1:2014.
NOTICE
LEDs
The camera illumination systems are fitted with light LEDs. These are assigned to risk group 1
according to IEC 62741:2006.
► Do not look into beam!