PCP-Manual-REV-C.pdf - 第39页
PCP Series Manual Revision B / October 2021 Page 39 of 56 Parts Break down PCP015 and PCP015-C PCP0 15 Bill of Materials Figure 47 : PCP015 Disassembled Item Part Number Description Qty 1 PCP- 015 - A3 MOTOR ASSEMBLY, PC…
PCP Series Manual
Revision B / October 2021
Page 38 of 56
K-Factor
The K-Factor multiplies the speed to increase or decrease motor speed by a percentage.
The system follows the equation below:
(Actual Material Ouput Weight) x (K-Factor) = (Expected Material Output Weight)
If there is not enough material, the K-Factor should be increased. If there is too much
material, the K-Factor should be decreased. To determine if the K-Factor needs to be
adjusted to get the right amount of material for your settings, set the flow rate and
dispense for X amount of ml/min. It is recommended to take 5-10 shots of the material and
weigh them to ensure the setting is correct. Most, if not all applications should fall into the
.8-1.2 range.
Example: If 10 ml/min is the expected output, but are getting an actual output of 9
ml/min after five shots, the K-Factor should be 1.11. This will speed up the motor to
110% and bring the material output to the expended output.
1. Select Manual from the cycle stop screen.
2. Select the PCP050 tab.
3. Select the K-Factor tab.
4. Enter the K-Factor for Pump B.
5. Select Apply to Auto to apply the set value to Auto Mode.
Figure 46: K-Factor Screen
PCP Series Manual
Revision B / October 2021
Page 39 of 56
Parts Breakdown
PCP015 and PCP015-C
PCP015 Bill of Materials
Figure 47: PCP015 Disassembled
Item
Part Number
Description
Qty
1
PCP-015-A3
MOTOR ASSEMBLY, PCP015
1
2
PCP-015-9
COUPLING, MOTOR, PCP015
1
3
PCP-015-A2
ROTOR ASSEMBLY, PCP015
1
4
PCP-015-7
SEAL BLOCK, PCP015
1
5
PCP-015-8
ROTARY SEAL, UHMW-PE, PCP015
3
6
PCP-015-G
O-RING, AN015, PCP015
3
7
PCP-015-A1
STATOR, FFKM, PCP015
1
8
PCP-015-2-A
LUER, STANDARD ADAPTER, PCP015
1
9
PCP-015-3
UNION CAP, PCP015
1
10
PCP-015-4
STATOR SLEEVE, SS, PCP015
1
11
PCP-015-5-TL
FLUID BODY, SS, LEFT PORTED, 1/4'' NPT, PCP015
1
12
PCP-015-6
BLEED CLIP, BLEED PORT, PCP015
1
13
PCP-015-B
O-RING, AS013, PCP015
1
14
PCP-015-C
O-RING, SS5, PCP015
3
15
PCP-015-F
O-RING, AN016, PCP015
1
16
PCP-015-A
O-RING, FKM, P9, PCP015
1
17
PCP-015-I
M3 X 35 MM SOCKET HEAD CAP SCREWS
2
18
PCP-015-H
M3 X 55 MM SOCKET HEAD CAP SCREWS
2
Figure 48: PCP015 Bill of Materials
PCP Series Manual
Revision B / October 2021
Page 40 of 56
PCP015-C Bill of Materials
Figure 49: PCP015-C Disassembled
Item
Part Number
Description
Qty
1
PCP-015-A3
MOTOR ASSEMBLY, PCP015
1
2
PCP-015-9
COUPLING, MOTOR, PCP015
1
3
PCP-015-A2-WC
ROTOR ASSEMBLY, TUNGSTEN CARBIDE, PCP015-C
1
4
PCP-015-7
SEAL BLOCK, PCP015
1
5
PCP-015-8
ROTARY SEAL, UHMW-PE, PCP015
3
6
PCP-015-G
O-RING, AN015, PCP015
3
7
PCP-015-A1-HFS
STATOR, HFS, PCP015-C
1
8
PCP-015-2-A
LUER, STANDARD ADAPTER, PCP015
1
9
PCP-015-3
UNION CAP, PCP015
1
10
PCP-015-4
STATOR SLEEVE, SS, PCP015
1
11
PCP-015-5-TL
FLUID BODY, SS, LEFT PORTED, 1/4'' NPT, PCP015
1
12
PCP-015-6
BLEED CLIP, BLEED PORT, PCP015
1
13
PCP-015-B
O-RING, AS013, PCP015
1
14
PCP-015-C
O-RING, SS5, PCP015
3
15
PCP-015-F
O-RING, AN016, PCP015
1
16
PCP-015-A
O-RING, FKM, P9, PCP015
1
17
PCP-015-I
M3 X 35 MM SOCKET HEAD CAP SCREWS
2
18
PCP-015-H
M3 X 55 MM SOCKET HEAD CAP SCREWS
2
Figure 50: PCP015-C Bill of Materials