CP6S-PAM操作手册.pdf - 第39页

Loading and Unloading the PCB • Press [LOAD PCB] to load a board to the reference pin on the XY-table. • Press [UNLOAD PCB] to unload a board. After pressing the ST ART button • When fiducial mark sequences exist in the …

The software reads the coordinates of placed parts using the mark camera and prepares

the data base necessary to calculate the placement accuracy deviations.

Function Key Menu

Automatic operation

Step operation

Monitor Display

Second Display Area

"Press START" displays if the start-up conditions are fulfilled.

An error message displays if the conditions are not met.

First Status Area : MEASURING

Function Key Operation

Auto: Press this to continuously read part locations.

Step: Press this to read part locations one sequence at a time

The START button must be pressed for each sequence.

RETURN: Returns to page 100 To page 100

Page120

CP_6.PROGRAM

000000000000

Prod 00000 Sche 00000

P1.00 off line

ST11N 3PAM

RETURN

jog

Step

MEASURING

C6PM6017

Operation : Front

Press START

STATUS

P Mode

Recovery

T Mode

PAM Mode

Product

E Pass

Joint

Auto RETURN

RETURNStep

Placement Result Measurement Measurement Page 120

6. Description of Commands

Version 3.0 6-6 CP-6 Series PAM Operation

Loading and Unloading the PCB

• Press [LOAD PCB] to load a board to the reference pin on the XY-table.

• Press [UNLOAD PCB] to unload a board.

After pressing the START button

• When fiducial mark sequences exist in the program, the software reads the

coordinates for the parts placed after reading the fiducial marks. The software

immediately starts reading the placement coordinates if no mark sequences exist.

• The error message "XY table not at lower limit" displays in the 1st display area

with Start input, if the XY-table is not in the lower-limit, and the software returns

to page 100.

• "No Board" displays in the 1st display area if the machine determines that no

board exists during a board check, and the software returns to page 100.

• Part processing begins with the first sequence placed by head-A.

• Coordinate data is not collected for parts that produce vision processing errors.

• The XY-table returns to the loading position once the software processes the last

coordinate data, without unloading the board. The software then totals the

measurement results and displays the message “Analyzing” in the 2nd display

area. The software returns to page 100 after calculating the data.

• The software monitor alarms are the same as in automatic operation. The software

returns to page 100 after reset button input if the machine stops due to an

abnormal condition. At this point, the message "Place from 1st sequence" displays

in the first display area, and and the machine will resume placement from the 1st

sequence.

The next sequence is performed if an abnormality does not initiate an emergency

stop.

• "Measuring" displays on the monitor in the 2nd display area after Start button

input. Sequence numbers (including mark sequences) are counted the same as in

the placing mode.

After pressing the CYCLE STOP button

The machine waits for START button input once again. The next process is performed

upon START button input.

Starting from the first Sequence

Move back one command level to restart the process from the first sequence after

stopping the machine during operation.

6. Description of Commands

Version 3.0 6-7 CP-6 Series PAM Operation

This displays the measured data. It also selects the nozzle type from the following data.

Function Key Menu

Monitor Display

• This display shows all nozzle and angle measurement data.

• The data displayed on the monitor represents the Avg. (average) dX, Avg. dY,

Max. dX, Max. dY, Min. dX, Min. dY, s in 1/1000 mm and Avg. dQ, Max dQ and

Min. dQ. in 1/1000°.

• The data used to calculate deviation is displayed in the middle right side of the

display.

Second Display Area : READY

First Status Area : DATA

Page140

CP_6.PROGRAM

000000000000

Prod 00000 Sche 00000

P1.00 off line

Operation : Front

Ready

RETURN

jog

SIZE

Data Save

Avg.dX

- 13

Max.dX

- 13

3sig.X

Avg.dQ

- 278

Max.dQ

476

Max.dQ

- 278

3sig.Q

483

- 9

Avg.dY

Max.dY

- 9

Max.dY

3sig.Y

DATA

Measurement Result

Nozzle Type

All Nozzle

All degrees

All data

5000

dXdY

[1/1000 mm]

[1/1000 deg]

C6PM6020

SIZE PRINT RETURN

Displaying the Data

Data display

Page 140

6. Description of Commands

Version 3.0 6-8 CP-6 Series PAM Operation