4OM-1050-002.pdf - 第179页

Error ID Item Description 080601 F d r .Crg. Axis Motor #1 Emergency stop Servo Error 080602 F d r .Crg. Axis Motor #1 Encoder error Servo Error 080603 F d r .Crg. Axis Motor #1 Mechatrolink cut error Servo Error 080604 …

100%1 / 345
Error ID Item Description
0805e5 Fdr.Crg. Axis Motor #1 WDT error
Servo Alarm
0805e6 Fdr.Crg. Axis Motor #1 Communication error
Servo Alarm
0805ea Fdr.Crg. Axis Motor #1 Servo pack error
Servo Alarm
0805eb Fdr.Crg. Axis Motor #1 Servo pack access error
Servo Alarm
0805ec Fdr.Crg. Axis Motor #1 Servo pack WDC error
Servo Alarm
0805ed Fdr.Crg. Axis Motor #1 Command not execute
Servo Alarm
0805f1 Fdr.Crg. Axis Motor #1 Power line open phase
Servo Alarm
080591 Fdr.Crg. Axis Motor #1 Overload warning
Servo Alarm
080592 Fdr.Crg. Axis Motor #1 Regenerative overload warning
Servo Alarm
080594 Fdr.Crg. Axis Motor #1 Data setting warning
Servo Alarm
080595 Fdr.Crg. Axis Motor #1 Command warning
Servo Alarm
080596 Fdr.Crg. Axis Motor #1 Communication warning
Servo Alarm
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
0210-004 2-62 AFO01ETRP
3.3 Error IDs and Remedial Procedures
Error ID Item Description
080601 Fdr.Crg. Axis Motor #1 Emergency stop
Servo Error
080602 Fdr.Crg. Axis Motor #1 Encoder error
Servo Error
080603 Fdr.Crg. Axis Motor #1 Mechatrolink cut error
Servo Error
080604 Fdr.Crg. Axis Motor #1 Location timeout
Servo Error
080605 Fdr.Crg. Axis Motor #1 Position error pulse overflow error
Servo Error
080606 Fdr.Crg. Axis Motor #1 Software limit (-)
Servo Error
080607 Fdr.Crg. Axis Motor #1 Software limit (+)
Servo Error
080608 Fdr.Crg. Axis Motor #1 Illegal parameter
Servo Error
080609 Fdr.Crg. Axis Motor #1 System error
Servo Error
08060a Fdr.Crg. Axis Motor #1 Illegal command
Servo Error
08060b Fdr.Crg. Axis Motor #1 Servo on time out
Servo Error
08060c Fdr.Crg. Axis Motor #1 Servo off time out
Servo Error
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the rem
080701 Fdr.Crg. Axis Motor#1 Interlock Movement cannot take place until the index angle is adjusted.
080702 Fdr.Crg. Axis Motor#1 Interlock Pallet went out.
080801 Fdr.Crg. Axis Motor#1 Communication error was detected.
Communication
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
0110-003 2-6 3 AFO01ETRP
3.3 Error IDs and Remedial Procedures
Error ID Item Description
090101 Fdr.Crg. Axis Motor #2 Origin Encoder origin was not detected.
090102 Fdr.Crg. Axis Motor #2 Origin Origin sensor (slide) was not detected.
090104 Fdr.Crg. Axis Motor #2 Origin Feedback value is indefinite.
090105 Fdr.Crg. Axis Motor #2 Origin The component pick-up (z) axis is not at origin.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
090201 Fdr.Crg. Axis Motor #2 Timing Task has not been completed unable to continue.
090301 Fdr.Crg. Axis Motor #2 Data The driver data was detected outside of the possible range.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
090401 Fdr.Crg. Axis Motor #2 Limit (+) Limit error has been detected.
090402 Fdr.Crg. Axis Motor #2 Limit (-) Limit error has been detected.
090403 Fdr.Crg. Axis Motor #2 Limit (+)(-)Limit error has been detected.
(Cause 1) Automatic or manual operation was started without all devices being zeroed after the
machine was powered and the [SYS CLEAR] button was pressed.
(Remedy 1) Press the [RETURN] button to cancel the error display.
Remove the cause of the error.
Zero all axes and re-start the operation.
0110-003 2-6 4 AFO01ETRP
3.3 Error IDs and Remedial Procedures