4OM-1050-002.pdf - 第286页
Error ID ltem Description 800D01 Maintenance Warning Trash box fill up warning.(notice count over) 800D02 Maintenance Warning Keep the machine condition. (maintenance cycle time : Oil-Checkup/Weekly) 800D03 Maintenance W…
0210-001 2-160-5 AFO01ETRP
3.3 Error IDs and Remedial Procedures
Error ID ltem Description
800901 Alarm For Shortage of Comp. The tape end was detected.
800902 Alarm For Shortage of Comp. Few components to feed.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
800A01 Product Information Finished product interval :
800A02 Product Information Auto run interval :
800A03 Product Information Nozzle usage interval :
800A04 Product Information Product started by RUN MODE “PASS” Operation.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
800B01 Machine Interface Signal No signal from furnace.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
800C01 Cancel Recovery on
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
Error ID ltem Description
800D01 Maintenance Warning Trash box fill up warning.(notice count over)
800D02 Maintenance Warning Keep the machine condition.
(maintenance cycle time : Oil-Checkup/Weekly)
800D03 Maintenance Warning Keep the machine condition.
(maintenance cycle time : Oil-Checkup/Monthly)
800D04 Maintenance Warning Keep the machine condition.
(maintenance cycle time : Oil-Checkup/3-Monthly)
800D05 Maintenance Warning Keep the machine condition.
(maintenance cycle time : Oil-Checkup/6-Monthlyy)
800D06 Maintenance Warning Keep the machine condition.
(maintenance cycle time : Oil-Checkup/Designate #1)
800D07 Maintenance Warning Keep the machine condition.
(maintenance cycle time : Oil-Checkup/Designate #2)
800D08 Maintenance Warning Keep the machine condition.
(maintenance cycle time : Upkeep-Checkup/Nozzle)
800D09 Maintenance Warning Keep the machine condition.
(maintenance cycle time : Upkeep-Checkup/Filter #1)
800D0A Maintenance Warning Keep the machine condition.
(maintenance cycle time : Upkeep-Checkup/Filter #2)
800D0B Maintenance Warning Keep the machine condition.
(maintenance cycle time : Designate-Checkup/Item #1)
800D0C Maintenance Warning Keep the machine condition.
(maintenance cycle time : Designate-Checkup/Item #2)
800D0D Maintenance Warning Keep the machine condition.
(maintenance cycle time : Designate-Checkup/Item #3)
800D0E Maintenance Warning Component box fill up warning.(notice count over)
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
800E01 Program Change Warning Check the setup of machine.(program change completed)
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
3.3 Error IDs and Remedial Procedures
0210-001 2-160-6 AFO01ETRP
Error ID ltem Description
801001 Auto Offset Teach Information Auto offset teach mode start.(this prcs. Completed)
801002 Auto Offset Teach Information Nozzle not found.
801003 Auto Offset Teach Information Nozzle Dirt Detection. If dirt has adhered, there is a possibil-
ity that it may become impossible to recognize. Please re-
move the ring lighting glass upper surface, a diffusion board,
and the dirt adhering to the nozzle.
801004 Auto Offset Teach Information Gain Level Teach Error.
801005 Auto Offset Teach Information Camera Dirt Detection. If dirt has adhered, there is a possibil-
ity that it may become impossible to recognize. Please re-
move the ring lighting glass upper surface, a diffusion board,
and the dirt adhering to the nozzle.
801006 Auto Offset Teach Information Nozzle center error.
801007 Auto Offset Teach Information Nozzle origin error.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Refer to the recognition error IDs that will appear with the error messages.
Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
801101 Feeder Carriage Priority Mode Return to order of priority carriage.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
3.3 Error IDs and Remedial Procedures
0307-002 2-160-7 AFO01ETRP