4OM-1050-002.pdf - 第215页

Error ID Item Description 150601 L 2 Conveyor Communication The controller can not run. 150602 L 2 Conveyor Communication Controller interior is out of order . 150603 L 2 Conveyor Communication Controller in communicatio…

100%1 / 345
Error ID Item Description
140201 P.C.B. LOCATE LEVER TIMING TASK HAS NOT BEEN COMPLETED UNABLE TO
CONTINUE.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
140301 P.C.B. LOCATE LEVER DATA THE DRIVER DATA WAS DETECTED OUTSIDE OF THE
POSSIBLE RANGE.
(Cause 1) The target value has exceeded the movable range of the device.
(Remedy 1) As the P.C.B. thickness has exceeded the specified value, set the data correctly.
140401 P.C.B. LOCATE LEVER LIMIT LIMIT ERROR HAS BEEN DETECTED. ; BPH94 E/NR
140402 P.C.B. LOCATE LEVER LIMIT LIMIT ERROR HAS BEEN DETECTED. ; BPH95 E/NR
(Cause 1) Dirt adheres to the sensor and the optical beam is shielded.
(Cause 2) The sensor may be defective.
(Remedy 1) Wipe off dirt on the sensor and re-zero the support pin up/down mechanism.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
(Remedy 2) Contact our service personnel for details.
140601 P.C.B. LOCATE LEVER THE CONTROLLER CAN NOT RUN.
COMMUNICATION
140602 P.C.B. LOCATE LEVER CONTROLLER INTERIOR IS OUT OF ORDER.
COMMUNICATION
140603 P.C.B. LOCATE LEVER CONTROLLER IN COMMUNICATION ERROR CONDITION.
COMMUNICATION
140604 P.C.B. LOCATE LEVER CONTROLLER INCOMPLETE RESULTING IN AN OVERTIME
ALARM.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
0207-004 2-98 AFO01ETRP
3.3 Error IDs and Remedial Procedures
Error ID Item Description
150601 L2 Conveyor Communication The controller can not run.
150602 L2 Conveyor Communication Controller interior is out of order.
150603 L2 Conveyor Communication Controller in communication error condition.
150604 L2 Conveyor Communication Controller incomplete resulting in an overtime alarm.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
160601 R2 Conveyor Communication The controller can not run.
160602 R2 Conveyor Communication Controller interior is out of order.
160603 R2 Conveyor Communication Controller in communication error condition.
160604 R2 Conveyor Communication Controller incomplete resulting in an overtime alarm.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
3.3 Error IDs and Remedial Procedures
0207-001 2-98-1 AFO01ETRP
Error ID Item Description
400101 Abnormal Front Safety Door The machine’s front safety door (lower) is open.
400102 Abnormal Front Safety Door The rotary hand wheel has been inserted.
(Cause 1) The front safety door was opened with the machine in the operation mode.
(Cause 2) The cam hand-rotating wheel is inserted into the motor shaft of the rotary turret.
(Remedy 1) Press the [RETURN] button to cancel the error display and press the [POWER]
button again. After the machine is powered up, perform the zeroing operation on
all axes.
(Remedy 2) Detach the cam hand-rotating wheel.
400201 Fdr.Crg. Axis Safety Guard The fdr.crg. #1 home location safety guard is open.
400202 Fdr.Crg. Axis Safety Guard The fdr.crg. #2A home location safety guard is open.
400203 Fdr.Crg. Axis Safety Guard The fdr.crg. #3B home location safety guard is open.
400204 Fdr.Crg. Axis Safety Guard The fdr.crg. #2B home location safety guard is open.
400205 Fdr.Crg. Axis Safety Guard The fdr.crg. #3A home location safety guard is open.
400206 Fdr.Crg. Axis Safety Guard The fdr.crg. #4 home location safety guard is open.
400207 Fdr.Crg. Axis Safety Guard The fdr.crg. Axis safety guard (a) is open.
400208 Fdr.Crg. Axis Safety Guard The fdr.crg. Axis safety guard (b) is open.
(Cause 1) The safety cover was opened while the feeder carriage was moving.
(Cause 2) The [START] button was pressed with the safety cover being open.
(Remedy 1) Close the safety cover.
(Remedy 2) Press the [RETURN] button to cancel the error display and then zero all axes.
0307-004 2-99 AFO01ETRP
3.3 Error IDs and Remedial Procedures