Manual_BSA_II_英文操作说明书.pdf - 第21页
BSA II Operating Instructions 21 Operating Design 4.6.3 “DEVICE“/“RS232“ Menu P arameters Settings Explanations DA T .RE C. XBPI Extended range of commands to con trol numerous balanc e functions with binary protocol for…
20 BSA II Operating Instructions
Operating Design
Parameters Settings Explanation
WT.UNIT GRAMS*, KI-
LOGR., CARATS,
POUNDS, OUNC-
ES, TROY.OZ., HK-
TAEL, SNGTAEL,
TWNTAEL,
GRAINS, PENY-
WT., MILLIGR.,
PTS./LB, CHN-
TAEL., MOMMES,
AUSTR.CT, TOLA,
BAHT, MESGHAL,
NEWTON
The device displays the weight in the selected unit.
The availability of units depends on national legislation and is therefore
country-specific.
DISP.DIG. ALL* “Show all decimal places”: All decimal places are shown in the display. The
setting change is not available on conformity-assessed devices.
MINUS 1 “Last decimal place off”: The last decimal place is switched off.
CAL./ADJ. EXT.CAL. The [Adjust] button starts an external calibration and adjustment process
with the preset adjustment weight.
E.CAL.USR. The [Adjust] button starts an external calibration and adjustment process
with the user-defined adjustment weight value.
INT.CAL.* The [Adjust] button starts an internal calibration and adjustment process.
CAL.SEQ. ADJUST* The adjustment starts automatically after the calibration.
CAL.-ADJ. The adjustment must be started or exited manually after calibration with the
[Confirm] button.
* Factory setting
4.6.2 “SETUP“/“GEN.SERV.“ Menu
Parameters Settings Explanation
MENU.RES. DEFAULT Resets the system settings to the factory default settings.
NO* Deactivates the option of resetting the device menu.
* Factory setting
BSA II Operating Instructions 21
Operating Design
4.6.3 “DEVICE“/“RS232“ Menu
Parameters Settings Explanations
DAT.REC. XBPI Extended range of commands to control numerous balance functions with
binary protocol for direct communication with the device.
SBI* Enables SBI communication. The data is output to a PC or control unit. En-
ables the use of ESC commands from a PC to control the basic balance
functions with ASCII protocol.
REM.DISP. Enables data output on another display.
YDP20 Sets the standard settings of YDP20 printers.
YDP30 Sets the standard settings of YDP30 printers.
OFF Deactivates the automatic data output.
BAUD 600, 1200, 2400,
4800, 9600*,
19200, 38400,
57600, 115200
Sets the baud rate to the selected value.
PARITY ODD* Applies an odd parity.
EVEN Applies an even parity.
NONE Does not apply a parity.
STOPBIT 1 BIT*
2 BITS
HANDSHK. SFTWARE Sets the handshake protocol to software handshake.
HRDWARE* Sets the handshake protocol to hardware handshake.
NONE Does not set a handshake protocol.
DATABIT 7 BITS Sets the number of data bits to 7.
8 BITS* Sets the number of data bits to 8.
* Factory setting
22 BSA II Operating Instructions
Operating Design
4.6.4 “DEVICE“/“USB“ Menu
Parameters Settings Explanations
DAT.REC.** XBPI Extended range of commands to control numerous balance functions with
binary protocol for direct communication with the device.
SBI* Enables SBI communication. The data is output to a PC or control unit. En-
ables the use of ESC commands from a PC to control the basic balance
functions with ASCII protocol.
REM.DISP. Enables data output on another display.
YDP20 Sets the standard settings of YDP20 printers.
YDP30 Sets the standard settings of YDP30 printers.
OFF Deactivates the data output.
BAUD** 600, 1200, 2400,
4800, 9600*,
19200, 38400,
57600, 115200
Sets the baud rate to the selected value.
PARITY** ODD* Applies an odd parity.
EVEN Applies an even parity.
NONE Does not apply a parity.
STOPBIT ** 1 BIT*
2 BITS
HANDSHK.** SFTWARE Sets the handshake protocol to software handshake.
HRDWARE Sets the handshake protocol to hardware handshake.
NONE* Does not set a handshake protocol.
DATABIT** 7 BITS Sets the number of data bits to 7.
8 BITS* Sets the number of data bits to 8.
DEV.USED NONE*, PRINT-
ER, VIRT.COM,
PC HOST, REM.
DISP.
Indicates which connection is detected at the USB port.
* Factory setting
** Are blocked if “PRINTER“ or “REM.DISP.“ are displayed under “DEV.USED“