LmrXP142机械手册.pdf - 第63页
2.1 Lubricating the XY -robot Arrow marks in the illustration indicate lubrication points. Black arrows indicate points where a grease gun is required. XP1ML201a (4) (4) (3) (3) (1) (2) Daphne Eponex No.2 ✔ ✔ ✔ ✔ T002Ea …
Lubrication Instructions
The machine's lubrication points are shown in the following pages. Please refer to these
tables and illustrations when lubricating the machine.
1. Begin by checking the illustration for the lubrication points. White arrows indicate
surfaces that require greasing or oil. Black arrows indicate grease fittings, and
signify that grease should be applied using a grease gun.
Note: Even LM blocks that do not have a nipple can be lubricated by applying grease
between the block and the LM rail (bearing mechanism). The grease that adheres to
the ball bearings and rollers will be taken into the LM block, thereby lubricating the
LM block.
2. The symbols shown below are used in illustrations to indicate the location, type,
and schedule for lubrication.
✔: Apply an appropriate amount of lubricant.
R: Apply small amounts for rust protection.
N/A: Lubrication prohibited.
3. Lubrication should be performed in accordance with the "lubrication schedule"
indicated in the tables.
The schedule periods are as follows:
Every day: Lubricate every day (24 hours), regardless of the machine
operation time.
Every week: Lubricate every 7 days, regardless of the machine operation
time.
Every month: Lubricate every month, regardless of the machine operation
time.
Every 3 months: Lubricate every 3 months, regardless of the machine operation
time.
4. Use the checklist provided at the end of this chapter to verify that all lubrication
tasks have been performed.
LM rail
(1)
(2)
LM block
XP1ML002E
Example:
Part 3 Chapter 2 Lubrication
Edition 3.0 3-2-3 XP-142E Mechanical Reference
2.1 Lubricating the XY-robot
Arrow marks in the illustration indicate lubrication points. Black arrows indicate points
where a grease gun is required.
XP1ML201a
(4)
(4)
(3)
(3)
(1)
(2)
Daphne Eponex No.2
✔
✔
✔
✔
T002Ea
Lubrication points
Schedule
1
2
3
4
Every 3 months
Every 3 months
Every 3 months
Every 3 months
✔ : Lubricate
Y-axis ball screw
X-axis ball screw
Y-axis LM
rails
X-axis LM
rails
Part 3 Chapter 2 Lubrication
Edition 3.0 3-2-4 XP-142E Mechanical Reference
2.2 Lubricating the Placing Head
Arrow marks in the illustration indicate lubrication points.
Refer to section “Lubricating the Placing Head (Piston Pin, Vacuum Pin and Vacuum Cut
Pin)” for the details of lubrication to (8), (9), (10) and (11).
5
6
7
8
9
10
11
Z-axis ball screws
Spline shaft
Gears
Nozzle up/down guide
Piston pin
Vacuum pin
Vacuum cut pin
Daphne Eponex
No.2
✔
✔
✔
N/A
N/A
N/A
N/A
AFC grease
N/A
N/A
N/A
✔
✔
✔
✔
T003Ec
Lubrication points
Schedule
Every month
Every month
Every 3 months
Every month
Every month
Every month
Every month
✔ : Lubricate N/A : Do not lubricate
Part 3 Chapter 2 Lubrication
Edition 3.0 3-2-5 XP-142E Mechanical Reference