XP-142E Operator's Guide-TUT-XP142-1.1E.pdf.pdf - 第31页

Setting the Scheduled Production Quantity Specify the number of panels that are scheduled to be produced using the production program currently selected for use. Procedure (During production preparation) 1. At the [Main]…

Changing the Production Program

Follow the procedure below to change the production program.

Note: Refer to the host system operation manual for the procedure for

transmitting production programs.

Procedure

1. At the [Main] screen, press [Production] then [Select Program]

to display the [Select Program] dialog box.

2. Click the [▼] button to select the location where the program

file is saved.

Hard disk: /sd0

Floppy disk: /fd0

A list of the available programs is displayed in a dialog box.

3. Select the desired program from the list, then press the

[Download] button to load that program. The name of the

loaded program displays on the title bar at the top of the

screen, indicating that this program is now active.

Note: If the nozzle arrangement in the program does not match the nozzles at

the machine, a warning message will be displayed. To produce with the

nozzles in the machine, press [YES]. Press [NO] and the [Nozzle

Editor] screen is displayed. Please refer to the XP-142E System

Reference manual for an explanation of the nozzle editor.

3.2 Production Programs

Chapter 3: Preparing for Production

TUT-XP142-1.1E

3-7XP-142E Operator’s Guide

Setting the Scheduled Production Quantity

Specify the number of panels that are scheduled to be produced using the

production program currently selected for use.

Procedure (During production preparation)

1. At the [Main] screen, press [Maintenance A] then [Operation

Settings] to display the operation settings [Select Mode] page.

2. Press the [Scheduled Panels] input field at the right of the

screen to display a ten-key pad. Enter the production quantity

and press [CR].

3. Press [Close] to return to the [Main] screen.

Procedure (During automatic production)

1. Press the [Scheduled Panels] number field at the left of the

[Automatic] screen.

Input the production quantity with the ten-key pad that is

displayed, and then press [CR].

Note: The [Scheduled Panels] quantity can be input from the [Auto] screen

when the quantity is [0] and the READY ON button is flashing.

Production quantity editing is enabled when the field is white.

XP1T3003E

Chapter 3: Preparing for Production

TUT-XP142-1.1E

3-8 XP-142E Operator’s Guide

Setting the Feeders

CP-6-series feeders are used on the machine. Refer to the separate CP feeder

maintenance manual regarding the procedure for setting parts.

The sticker that is affixed to the side of each feeder is printed with a code

indicating the standards for that feeder.

Example: W D 08 04 - - - - -

W: Indicates that the feeder is a CP-6 feeder.

D: This indicates the feeder is a paper tape feeder while "E" represents an

embossed tape feeder.

08: This indicates that a tape with a width of 8 mm can be set on the

feeder.

04: This signifies that the pitch of the feeder is 4 mm.

Notes:

1. When setting feeders in the MFU, be sure that there are no objects (chip

fragments, etc.) between the feeder and the MFU. Remove any foreign

objects from the MFU grooves and from the bottom face of the feeder.

2. Verify that the tape leaf is not deformed.

3. Place the part tapes in their dedicated feeders. A part tape placed in the

wrong feeder may prevent the tape leaf from closing properly.

4. Hold the reel retainer up with a clip.

Clip

XP1T3001E

3.3 Part Settings

Chapter 3: Preparing for Production

TUT-XP142-1.1E

3-9XP-142E Operator’s Guide