00194103-01.pdf - 第176页
7 Options User Manual SIP LACE F5 HM 7.1 Nozzle changer for the 12-segment C ollect&Place head S oftware Version SR .408.xx 03/2006 US E dition 176 Fig. 7.1 - 2 Magazine and nozz le garages (1) Positio ning fi ducial…
User Manual SIPLACE F5 HM 7 Options
Software Version SR.408.xx 03/2006 US Edition 7.1 Nozzle changer for the 12-segment Collect&Place head
175
There is a positioning fiducial for position detection on each magazine of the nozzle changer. The
magazine locations are identified by numbers 1 to 7 on the nozzle changer. The nozzle garages
in the magazines are numbered consecutively from 1 to 12 (see Fig. 7.1 - 3
).
PLEASE NOTE 7
Special magazines are available upon request (contact Siemens A&D for details) and will be
numbered differently. 7
Picking up a nozzle
– The Collect&Place head Z axis moves down.
– The locking plate (item 3 in Fig. 7.1 - 2
) opens and releases the nozzles.
– The nozzle is picked up by the sleeve of the Collect&Place head.
– The Z axis moves up.
Setting down a nozzle
– The locking plate (item 3 in Fig. 7.1 - 2) opens and releases the nozzles.
– The Collect&Place head Z axis moves down and sets the nozzle down.
– The locking plate closed.
– The Collect&Place head Z axis moves up.
Discarding defective nozzles
– The Collect&Place head Z axis moves down 14 mm towards the discarding device (item 2 in
Fig. 7.1 - 1
) and thus moves the defective nozzle into the hole in the discarding device.
– The Z axis moves up again and the nozzle is stripped from the sleeve by spring wires.
– The nozzle drops into the used tape channel container (item 3 in Fig. 7.1 - 1
).
7 Options User Manual SIPLACE F5 HM
7.1 Nozzle changer for the 12-segment Collect&Place head Software Version SR.408.xx 03/2006 US Edition
176
Fig. 7.1 - 2 Magazine and nozzle garages
(1) Positioning fiducial
(2) Locking plate
(3) Nozzle garage
(4) Hole for the parallel pin (7) for centering the magazines
(5) Hole for the parallel pin of the slide mechanism
(6) Slot for the parallel pin (7) for centering the magazines
(7) Parallel pin for centering the magazines
(8) Parallel pins to open and close the locking plate
(9) Magazines
User Manual SIPLACE F5 HM 7 Options
Software Version SR.408.xx 03/2006 US Edition 7.1 Nozzle changer for the 12-segment Collect&Place head
177
7.1.4 Notes on operation
Æ When you fill a magazine with a certain nozzle type for the first time, attach an adhesive label
to identify the type.
PLEASE NOTE 7
Fill the magazines off the machine and always replace complete magazines. 7
Æ Open the locking plate and place the nozzles in the nozzle garages.
Æ Close the locking plate so that the nozzles cannot drop out of the magazines.
CAUTION 7
Before you fill magazine, make sure that all the nozzles on the Collect&Place head have
been returned to their magazines. 7
Æ Programming the nozzle changer is described in the SIPLACE Pro user manual.
PLEASE NOTE 7
Æ Do not allow components to drop onto the magazines. If they do, they could jam the locking
plate.
Æ Do not allow components to drop onto free feeder module locations. They will stick to the
magnetic bar. Production may have to be interrupted if the feeder modules are not placed on
the component table correctly. You should therefore regularly clean the magazines and free
locations.