DEK INFINITY USER MANUAL.pdf.pdf - 第128页
INFINITY 6(735()(5(1 &(6 35()(5(1&(6 2.2 User Manual Software Version 7 PREF ERENC ES T ransport Mode Sets the input and output side of the printer , options are: Machine Uni ts Sets the unit of measure ment, op…
INFINITY
6(735()(5(1&(6
,1752'8&7,21
Software Version 7 User Manual 2.1
CHAPTER 2 SET PREFERENCES
INTRODUCTION The Set Preferences function allows for the setting of preferred machine control
options.
To access the set preferences window proceed as follows:
1. Select Maint. (F8).
2. Select Set Prefs (F5).
The set preferences window is displayed:
The menu bar changes to give the following options:
Next and Previous move the highlight between the various parameters.
Incr. and Decr. alter the value of the highlighted parameter.
Run Head
Paste
Load
Clean
Screen
Adjust Setup Monitor Maint.
Calibrat
Pressure
Calibrat
Offset
Calibrat
Vision
House
Keeping
Set
Prefs
Diagnost
Tes t
Cycles
Exit
Set Preferences
secs
..more
TRANSPORT MODE
MACHINE UNITS
UPLINE PROTOCOL
DOWNLINE PROTOCOL
TRANSFER PERIOD
SELECTIVE PRINT/PASS
PASTE DISPENSE POS.
COMMS PROTOCOL
EVENT RECORDING
TOOLING HARDWARE
FIDUCIAL REFERENCE
PRODUCT BARCODE H/W
SCREEN BARCODE H/W
REMOTE BARCODE H/W
LEFT TO LEFT
Metric
NO FMI
NO FMI
20
ENABLED
FRONT
NO COMMS
GROUP 3
MAGNETIC
LEFT
NOT FITTED
NOT FITTED
NOT FITTED
Next Previous Incr. Decr. Exit
INFINITY
6(735()(5(1&(6
35()(5(1&(6
2.2 User Manual Software Version 7
PREFERENCES
Transport Mode Sets the input and output side of the printer, options are:
Machine Units Sets the unit of measurement, options are:
Upline Protocol Sets the protocol for transferring boards from adjacent machines, options are:
Downline Protocol Sets the protocol for transferring boards to adjacent machines, options are:
Transfer Period Sets a programmable time period used by certain transfer protocols, options are:
Period of Transfer Time - This is the period of time which the machine allows
for a transfer of a board before displaying a ‘Board Transfer Error’ for upline
or downline.
Period of Waiting Time - This is the period of time which the machine allows
when waiting for the upline or downline machine to request a board for transfer
before displaying a message of ‘Waiting for Upline/Downline’.
Options Default
Left to Right Left to Right
Right to Left
Right to Right
Left to Left
No Transfer
Options Default
Metric Metric
Imperial
Options Default
No FMI Specified by Customer
Requirements
MIU
Manual
Options Default
No FMI Specified by Customer
Requirements
MIU
Manual
Minimum Maximum Increment Default
0 Seconds 999 Seconds 1 Second 20 seconds
INFINITY
6(735()(5(1&(6
35()(5(1&(6
Software Version 7 User Manual 2.3
Selective Print/Pass Sets whether the facility to selective print or pass through a board is to be used,
options are:
This feature is protected by Feature Licence Authentication.
When enabled the identity of the incoming board is checked using a separate
fiducial on the board only, called a Select Mark. If the identity of the board
matches the current product file the board is printed. If the board is different or
cannot be recognized, it is passed through without printing.
Paste Dispense
Position
Sets the position from which paste is dispensed, in relation to the screen image,
options are:
When exiting set preferences after setting option to either Rear or Auto the
following window is displayed:
Comms Protocol Sets the communications protocol to be used for serial communications to a host
computer, options are:
The menu bar changes depending on the option chosen, see the Host
Communications Chapter for further details.
WARNING
HOST COMMUNICATIONS. BE AWARE THAT IF THE MACHINE SAFETY LOCKS
ARE DEFEATED WHILST HOST COMMUNICATIONS ARE ACTIVE, A DANGER
EXISTS WHEREBY MACHINE PARTS MAY MOVE UNEXPECTEDLY.
Options Default
Enabled Disabled
Disabled
Options Default
Front Auto
Rear
Auto
Please confirm that there will be no obstruction
when your paste dispenser dispenses paste at the
rear of the image
Paste Dispense Position
Options
GEM
Net_File
No Comms