DEK INFINITY USER MANUAL.pdf.pdf - 第62页
INFINITY 0$&+,1( 352*5$ 00,1* 67$*() $87 2)/(;722/,1* 1.60 User Manual Software Versi on 7 The Autoflex Matrix window is displayed: The Autoflex pin matrix has already be en setup for this product from the boa…
INFINITY
0$&+,1(352*5$00,1*
67$*()$872)/(;722/,1*
Software Version 7 User Manual 1.59
STAGE 6F - AUTOFLEX TOOLING
WARNING
BOARD CLAMPS. EXTREME CARE MUST BE EXERCISED WHEN WORKING IN
THE TOOLING AREA OF THE MACHINE TO AVOID INJURY. THE FOILS ON THE
FRONT AND REAR BOARD CLAMPS ARE VERY SHARP.
CAUTION
BOARD CLAMPS. Care must be taken to ensure that the board clamps
are not damaged when removing or replacing tooling.
The correct pins for each product are selected automatically when the board size
parameters are programmed into the product file. If the pin configuration needs
to be amended, for example if a support pin coincides with the position of an
underside component and needs to be removed, from the setup page:
1. Select Change Tooling (F6).
The Change Tooling Parameters window is displayed:
The parameters are not active.
2. Select Adjust (F1). The parameters are now active.
3. Select Change Autoflex (F1).
Mode
Load
Data
Edit
Data
Setup
Squeegee
Change
Screen
Change
Tooling
Change
Language
Exit
Change Tooling Parameters
BOARD WIDTH
BOARD STOP X
BOARD STOP Y
216.0
125.0
142.6
mm
mm
mm
Adjust
Raise
Head
Remove
Cleaner
Board
Stop
Full
Width
Load
Width
Print
Height
Exit
Change
Autoflex
Save Next Previous Incr. Decr. Exit
INFINITY
0$&+,1(352*5$00,1*
67$*()$872)/(;722/,1*
1.60 User Manual Software Version 7
The Autoflex Matrix window is displayed:
The Autoflex pin matrix has already been setup for this product from the
board dimensions.
4. Use the Left, Right, Up and Down keys (F4 - F7), to select the pin positions
required for editing.
5. Use the Lower and Raise keys (F1 - F2), to select or deselect the pins.
6. Select Exit (F8).
7. Select Save (F2).
8. Select Exit (F8).
Autoflex Matrix
14
13
12
11
10
9
8
7
6
5
4
3
2
1
AB CDEF GH I J KLMN
---------------
---------------
---------------
---------------
---------------
---------------
---------------
---------------
---------------
---------------
---------------
---------------
---------------
---------------
O
Lower Raise Reset Left Right Up Down
Exit
Lower Raise Reset Left Right Up Down
Exit
Lower Raise Reset Left Right Up Down
Exit
Change
Autoflex
Save Next Previous Incr. Decr. Exit
Change
Autoflex
Save Next Previous Incr. Decr. Exit
INFINITY
0$&+,1(352*5$00,1*
67$*()$872)/(;722/,1*
Software Version 7 User Manual 1.61
9. Select Exit (F8).
10.Select Exit (F8). The rail moves to the board width and the selected Autoflex
pins rise.
11. Select Setup (F6).
12.Select Change Tooling (F6).
13.Select Board Stop (F4). The camera moves to the board stop position. The
board stop on the camera extends.
14.Select Raise Head (F2).
15.Raise the printhead using two button control.
Adjust
Raise
Head
Remove
Cleaner
Board
Stop
Full
Width
Load
Width
Print
Height
Exit
Mode
Load
Data
Edit
Data
Setup
Squeegee
Change
Screen
Change
Tooling
Change
Language
Exit
Run Head
Paste
Load
Clean
Screen
Adjust Setup Monitor Maint.
Mode
Load
Data
Edit
Data
Setup
Squeegee
Change
Screen
Change
Tooling
Change
Language
Exit
Adjust
Raise
Head
Remove
Cleaner
Board
Stop
Full
Width
Load
Width
Print
Height
Exit
Adjust
Raise
Head
Remove
Cleaner
Home
Camera
Full
Width
Load
Width
Print
Height
Exit