DEK INFINITY USER MANUAL.pdf.pdf - 第273页
INFINITY ',163(& 7,21 ',163(&7,2 16(7 83 Soft ware Ver sion 7 User Manual 8.33 12. If lighting is chan ged the following menu bar is displayed: Select the following button to adopt the changes to: …
INFINIT
Y
',163(&7,21
',163(&7,216(783
8.32 User Manual Software Version 7
a. Select Toggle Paste.
NOTE
Selecting toggle paste either shows or hides the paste display overlay onto
the monitor. The toggle paste facility on the board image is only functional
with the board inspection type set to advanced. Toggling paste on the
stencil is only available on Horizon and Infinity machines and only with
the stencil inspect type set to advanced.
b. Ensure that the paste display overlay coincides with the presence of paste.
If this is correct go to Step 19. If this is incorrect, note the position of the
non-existent paste and continue with Step 7.
NOTE
If the paste display overlay coincides with the presence of paste, any poor
inspection results are due to process problems and not 2Di setup.
c. Ensure that the inspection results are consistent with the amount of paste
on the pad. If this is correct go to Step 19. If this is incorrect continue
with Step 7.
7. Select Exit.
8. Select Edit Site.
9. Select Light Setup.
10.Adjust the lighting parameters to improve the lighting conditions in the
suspect areas.
11. Select Exit.
NOTE
Record Image button is displayed if Image Recording is enabled in Set
Preferences.
Auto
Scale
Toggle
Paste
Next Previous
Save
Image
Exit
Auto
Scale
Toggle
Paste
Next Previous Exit
Edit
Global
Edit
Limits
Delete
Site
Next
Site
Previous
Site
Edit
Site
Inspect
Site
Exit
Light
Setup
Next Previous Incr. Decr. Exit
Record
Image
Next Previous Incr. Decr. Exit
INFINITY
',163(&7,21
',163(&7,216(783
Software Version 7 User Manual 8.33
12.If lighting is changed the following menu bar is displayed:
Select the following button to adopt the changes to:
• ‘Apply to Full Set’ - to update only this device
• ‘Apply to All ’ - all learnt sites
• ‘Exit’ - just the current site
13.Select Exit.
14.Select Exit.
15.Select Step to step through inspection routine.
16.Select Exit to remove board from machine.
17.Place a clean board onto the machine rails and clean the stencil (Clean
Screen).
18.Repeat Steps 4 - 8.
19.Select Auto Scale.
Selecting auto scale automatically adjusts the paste scaling value for the
current site, to cause the value of paste present, on the pad currently selected
in the inspection result list, to be reported as 100%. The inspection results
window is updated accordingly. If the calculated value for paste scaling falls
outside the range of allowable values, an error window is displayed and the
paste scaling value is set to the limit nearest the calculated value. However,
if the currently selected paste present value is zero, no adjustment of the paste
scaling value takes place and an error window is displayed. A prompt is
displayed giving the new scaling factor value each time it is changed. The
auto scale button is only present if board inspection is being performed.
Apply to
Full Set
Apply to
All
Exit
Light
Setup
Next Previous Incr. Decr. Exit
Edit
Global
Edit
Limits
Delete
Site
Edit
Site
Inspect
Site
Exit
Step
Inspect
Setup
Single Exit
Edit
Global
Edit
Limits
Delete
Site
Edit
Site
Inspect
Site
Exit
Auto
Scale
Toggle
Paste
Next Previous
Save
Image
Exit
INFINIT
Y
',163(&7,21
',163(&7,216(783
8.34 User Manual Software Version 7
20.Select Exit.
21.Select Exit.
22.Select Step to remove the board from the machine.
23.Clean the board and stencil.
24.Carry out Section How to Add a Site and create all required sites, using the
same lighting parameters as before (see Auto Learn).
25.On completion carry out Section Inspect.
26.Set required 2D inspect rate and the Min site/cycle parameters in edit global.
27.This completes the 2Di setup. Commence print run in auto mode.
NOTE
During production use Adjust Inspect to fine tune the inspection process.
Auto
Scale
Toggle
Paste
Next Previous
Save
Image
Exit
Edit
Global
Edit
Limits
Delete
Site
Edit
Site
Inspect
Site
Exit
Step
Inspect
Setup
Single Exit