DEK INFINITY USER MANUAL.pdf.pdf - 第295页
INFINITY &21680$ %/(5( 3/(1,6+0(1 76 3$67(/2$ ',1* Soft ware Ver sion 7 User Manual 9.11 10. If the set preference is set to pause, the tricoloured beacon shows r ed and the following window is displayed: 11 .…
INFINITY
&21680$%/(5(3/(1,6+0(176
3$67(/2$',1*
9.10 User Manual Software Version 7
If the Camera Idle Position in Set Preferences is set to Behind Rail, the
following window and menu bar is displayed:
Selecting Continue Run clears the warning window and the print cycle
continues.
Selecting End Run clears the warning window, the print cycle is aborted and
control is returned to the ready page.
If the Unload Board Start in Set Preferences is set to Separation, the follow-
ing window and menu bar is displayed:
Selecting Continue Run clears the warning window and the print cycle
continues.
Selecting End Run clears the warning window, the print cycle is aborted and
control is returned to the ready page.
NOTE
If Camera Idle Position is set to Behind Rail and Unload Board Start is set
to Separation, the warning windows appear one after the other in the order
shown above.
9. Repeat Steps 1, 2 and 22.
Camera Behind Rail Warning
The CAMERA HOME POSITION is set to 'Behind
Rail'
Ensure that no tooling pins or other
obstructions are on the table behind the
rear rail, as these could cause damage to
the camera.
This option will only have an effect for
boards that are less than 250mm wide.
This option can be disabled from the set
preference page.
Continue
Run
End
Run
Unload Board Speedup Warning
The UNLOAD BOARD SPEEDUP option is set to
'Separation'
With this option enabled it should be noted
that there is only a minimal clearance
between the underside of the board and any
tooling being used, while the board is being
unloaded.
This option must not be used for boards that
are populated on the underside, as this
could damage the boards.
Continue
Run
End
Run
INFINITY
&21680$%/(5(3/(1,6+0(176
3$67(/2$',1*
Software Version 7 User Manual 9.11
10.If the set preference is set to pause, the tricoloured beacon shows red and the
following window is displayed:
11. Select Refill Paste (F1). The message ‘Select Load Cart to load the
cartridge or exit to abort.’ is displayed.
NOTE
Select Defer to continue printing without replacing the paste cartridge.
12.Select Load Cart. (F1). The message ‘Open the cover and load the new
paste cartridge then close Cover, press System Button and press Con-
tinue’ is displayed.
13.Carry out Steps 3-9 of Fitting a New Paste Cartridge procedure, later in this
section.
14.Select Continue (F1).
15.Go to Step 21.
16.If the set preference is set to suspend, the tricoloured beacon shows red and
the following window is displayed:
17.Select Refill Paste (F1). The message ‘Select Load Cart to load the
cartridge or exit to abort.’ is displayed.
NOTE
Select End Run to terminate the print run without replacing the paste
cartridge.
Pause on Warning
Print Medium Low. Please replenish.
Refill
Paste
Defer
Load
Cart.
Exit
Continue
Open
Cover
Suspend on Warning
Print Medium Low. Please replenish.
Refill
Paste
End
Run
INFINITY
&21680$%/(5(3/(1,6+0(176
3$67(/2$',1*
9.12 User Manual Software Version 7
18.Select Load Cart. (F1). The message ‘Open the cover and load the new
paste cartridge then close Cover, press System Button and press Con-
tinue’ is displayed.
19.Carry out Steps 3-9 of Fitting a New Paste Cartridge procedure, later in this
section.
20.Select Continue (F1).
21.Select Auto Dispense (F1).
22.After the dispense routine has been completed, press Exit (F8).
Fitting a New Paste
Cartridge
It is necessary at intervals to fit a new paste cartridge into the paste dispenser. If
there is no cartridge in the dispenser or the cartridge is empty, the warning
window ‘Print Medium Low. Please Replenish.’ is displayed.
If the consumable action option in set preferences is set to suspend, the paste
dispenser is checked to ensure availability of paste, before allowing a print run
to start. If paste isn’t available the warning window ‘Print Medium Low.
Please Replenish.’ is displayed.
WARNING
SOLDER PASTE AND SOLVENTS. WHEN USING OR HANDLING ANY SOLDER
PASTE OR SOLVENT FORMULATION THE MANUFACTURERS’ RECOMMEND
SAFETY PRECAUTIONS MUST BE STRICTLY ADHERED TO.
WARNING
PROTECTIVE CLOTHING. APPROVED PROTECTIVE CLOTHING SHOULD BE
WORN BY SOLDER PASTE AND SOLVENT HANDLERS AT ALL TIMES TO
ELIMINATE FUME INHALATION, EYE CONTACT, SKIN CONTACT AND
INGESTION.
To replace the paste cartridge carry out the following:
1. Press Paste Load (F3).
2. Press Load Cart. (F4). The print carriage drives to the front of the machine
and the dispenser rises to the vertical position. A message is displayed on
the screen ‘Open cover and replace Paste Cartridge’.
Load
Cart.
Exit
Continue
Open
Cover
Auto
Dispense
Manual
Load
Load
Cart.
Print
Directn
Exit
Auto
Dispense
Manual
Load
Load
Cart.
Print
Directn
Exit
Run Head
Paste
Load
Clean
Screen
Adjust Setup Monitor Maint.
Auto
Dispense
Manual
Load
Load
Cart.
Print
Directn
Exit