KE-3020_SPE_EN.pdf

KE - 3020 / 3020R PRODUCT S PECIFICATIONS Hi gh -S peed Flexi ble Mounter

KE-3020 / 3020R

PRODUCT SPECIFICATIONS

High-Speed Flexible Mounter

Important

(1) No part of this document may be copied or reproduced without the prior

permission of JUKI Corporation. (Including software and program)

(2) The contents of this document are subject to change without notice.

(3) This manual is prepared with extreme care. However, if you have any question

or ﬁnd any error or omission in writing, contact our dealer or JUKI Corporation.

(4) JUKI Corporation shall disclaim all the responsibility for any trouble resulting

from the user's abnormal operation regardless of Item (3).

(5) Microsoft, Windows are registered trademarks or trademarks of Microsoft

Corporation in the United States and /or other countries.

The company names and product names mentioned in this document are

generally registered trademarks or trademarks of the respective companies.

Table of contents

1. Introduction .................................................................................................................... 1

1.1. General .............................................................................................................................. 1

2. Features .......................................................................................................................... 2

3. System Configuration .................................................................................................... 6

3.1. KE-3020 System Configuration .......................................................................................... 6

3.2. KE-3020R System Configuration ....................................................................................... 7

4. Specifications ................................................................................................................ 8

4.1. Features of each model ..................................................................................................... 8

4.2. Mechanical/Electrical Specifications .................................................................................. 9

4.2.1. Usage environment conditions ........................................................................................ 9

4.2.2. Outside dimension (except for the largest projections) ................................................. 10

4.2.3. Mass .............................................................................................................................. 10

4.3. Component placement Cycle Time

(The Number of Component to Be Placed Per Hour) ................................................. 11

4.4. Nozzles ............................................................................................................................ 12

4.5. Applicable Component ..................................................................................................... 13

4.5.1. Applicable component sizes .......................................................................................... 13

4.6. Component Placement Accuracy at X, Y and θ ................................................................ 14

4.7. Applicable PWBs ............................................................................................................. 15

4.7.1. PWBs transport direction ............................................................................................... 15

4.7.2. PWB sizes and Mass..................................................................................................... 15

4.7.3. Unavailable areas for placing components on the board .............................................. 16

4.7.4. Unavailable areas for setting up the support pins ......................................................... 16

4.7.5. Area where components can be placed on the board (top and bottom) ...................... 18

4.7.6. Function correcting the PWB positions .........................................................................

5. Standard Functions And Optional Functions ............................................................ 22

5.1. Standard .......................................................................................................................... 22

5.1.1. Component database function ...................................................................................... 22

5.1.2. Height Measurement System (HMS) ............................................................................ 22

5.1.3. Feeder Float Detecting Sensor ..................................................................................... 22

5.1.4. Vacuum pump ............................................................................................................... 22

5.2. Option .............................................................................................................................. 23

5.2.1. Bad Mark Reader (Factory-Set Option) ........................................................................ 23

5.2.2. Feeder Changeover Function (Factory-Set Option) ..................................................... 23

5.2.3. Non-Stop Operation (Factory-Set Option) .................................................................... 23

5.2.4. Components verification System (CVS) (Factory-Set Option) ...................................... 24

5.2.5. SOT Direction Check Function (Factory-Set Option) .................................................... 24

5.2.6. Load control function (Factory-Set Option) ................................................................... 25

5.2.7. Rear Side Operation Unit (Factory-Set Option) ............................................................ 25

5.2.8. Feeder Indicator Function (FPI) (Factory-Set Option) .................................................. 25

5.2.9. MNVC (Factory-Set Option) .......................................................................................... 26

5.2.10. High resolution camera (Factory-Set Option) ............................................................. 27

5.2.11. Coplanarity (Factory-Set Option) ................................................................................ 28

5.2.12. Offset Placement After Solder Screen-printing (Factory-Set Option) ......................... 29

5.2.13. Earth Leakage Circuit Breaker (Option to Be Installed at the Factory) ...................... 30

5.2.14. Fluxer (Option to Be Installed at the Factory) ............................................................. 30

5.2.15. Main Line Filter (Option to Be Installed at the Factory) .............................................. 31

5.2.16. Ionizer (Option to Be Installed at the Factory) ............................................................ 31

5.2.17. IC Collection Belt (Option) ...........................................................................................

5.2.18. Tape Cutter Unit (Option for the electric type of bank) ............................................... 31

5.2.19. Automatic Tape Cutter (Option) .................................................................................. 31

5.2.20. Connector Bracket (Option Designed for the Fixed Bank).......................................... 31

5.2.21. FCS (Option) ............................................................................................................... 32